jcb 1T-2 High Tip Quick Start Manual Download Page 23

Page: 23 / 32

1T-2 High Tip Site Dumper

Fluids & lubrication

Item

Capacity

Fluid/Lubricant

JCBPart

Number

Container

Size*

Specification

Fuel tank

30L

Diesel

Refer to ‘Fuel’

Engine (oil)

4.4L (max)

3.4L (min)

JCB Engine Oil

EP 15W40

4001/1805

20L

ACEA ES/B3/A3,

API CH-4/SJ

Engine coolant

3.4L

JCB Antifreeze

HP/Coolant

4006 / 1120

20L

ASTM D6210

Hydraulic fluid
(including motors)

28L

JCB Hydraulic Fluid

OP46

4002 / 2005

20L

Grease points

As required

JCB Special

HP Grease

4003 / 2017

0.4kg

* For information about the different container sizes that are available (and their part numbers), please contact your JCB dealer.

JCB part numbers are liable to change and may also vary by region. For the latest information, always
check with your dealer/distributor.

General

Notice:

No warranty liability will be accepted for engine failures where unacceptable fuel grades

(or their equivalent) have been used at any stage.

Summary of Contents for 1T-2 High Tip

































Search results

Summary of Contents for 1T-2 High Tip

Reviews:

Related manuals for 1T-2 High Tip

Brands by name

Popular brands

jcb 1T-2 High Tip, Quick Start Manual

Search results

Summary of Contents for 1T-2 High Tip

Reviews:

Related manuals for 1T-2 High Tip

Brands by name

Popular brands