background image

 03 - Attachments, Couplings and Load Handling

 10 - Excavator End Quickhitch

 00 - General

03 - 9

9813/7900-2

03 - 9

Remove and Install

General

WARNING

  Always  install  the  quickhitch  latch

hook  locking  pin  (mechanical  only).  Failure  to

install the pin will result in possible failure of the

latching mechanism. Such a failure could result

in the sudden release of an attachment from the

machine  and  you  or  others  could  be  killed  or

seriously injured.

WARNING

  The  attachment  will  move  when

released.  Stand  clear  and  to  one  side  when

releasing the attachment.

WARNING

 The quickhitch sequence must not be

entered unless a constant tone buzzer is heard.

This can be identified on start up of the machine.

Check the constant tone buzzer operation daily.

CAUTION

  When  the  quickhitch  is  installed  and

its attachment attached, It is possible to strike the

cab and the underside of the boom or dipper with

some attachments. Use great care with the boom

and dipper to keep the attachment away from the

operator cab.

CAUTION

 When the quickhitch is attached to the

machine, allowance must be made for the weight

of the quickhitch on the rated operating load. The

mass of the Quickhitch is stamped on the data

plate.

The excavator Quickhitch, which is attached to the

dipper  enables  fast  removal  and  installation  of  the

bucket (and other attachments).

There are two types of Quickhitch available - manual

and hydraulic.

Compatibility of the Quickhitch must be checked with

Quickhitch manufacturer. For the Quickhitch system

pressure figures: 

Refer to: PIL 30-00-00.

 

Put the Quickhitch attachments on solid, level ground

to make the installation procedure safe and easier.

Installation

This  operation  is  easier  done  by  two  people,  one

person to operate the controls and one to line up the

pivots.

1. Before  the  Quickhitch  is  installed,  make  sure

that  the  tipping  lever  locking  bolt  assembly  is

attached with the nut and any lifting shackle is

removed.

2. Put the Quickhitch on solid, level ground. Use the

safe  and  correct  lifting  equipment  to  move  the

Quickhitch.

3. Move  the  machine  so  that  the  dipper  arm  and

Quickhitch are correctly aligned as shown. Refer

to Figure 7.

4. Engage the dipper:

4.1. Operate  the  controls  to  line  up  the  hole

in  the  dipper  arm  with  the  holes  in  the

Quickhitch.

4.2. Install the pivot pin and secure it with the nut

and bolt.

5. Engage the bucket link:

Summary of Contents for 16c-1




















































Reviews: