JBSYSTEMS Light Atom LED, Operation Manual

Page: 4 / 15

ENGLISH OPERATION MANUAL
JB SYSTEMS ® 3/26 ATOM
DESCRIPTION:
1.Optical lens
2.Hanging bracket with 2 knobs on both sides to fasten the unit and a mounting hole to fix a mounting hook.
3.15Vdc input, connect the supplied AC/DC-mains adapter here.
4.Microphone sensitivity
5.Dual 1\4 inch Stereo jack: Used to create
synchronous operations with multiple ATOM
effects.

Input: is used to connect a jack cable that
comes from the output of a previous ATOM.

Output: is used to connect a jack cable that
goes to the input of the next ATOM.
OVERHEAD RIGGING

Important: The installation must be carried out by qualified service personal only. Improper
installation can result in serious injuries and/or damage to property. Overhead rigging requires
extensive experience! Working load limits should be respected, certified installation materials
should be used, the installed device should be inspected regularly for safety.

Make sure the area below the installation place is free from unwanted persons during rigging, de-rigging
and servicing.

Locate the fixture in a well ventilated spot, far away from any flammable materials and/or liquids.

The device should be installed out of reach of people and outside areas where persons may walk by or be
seated.

Before rigging make sure that the installation area can hold a minimum point load of 10times the device’s
weight.

Always use a certified safety cable that can hold 12times the weight of the device when installing the unit.
This secondary safety attachment should be installed in a way that no part of the installation can drop
more than 20cm if the main attachment fails.

The device should be well fixed; a free-swinging mounting is dangerous and may not be considered!

Don’t cover any ventilation openings as this may result in overheating.

The operator has to make sure that the safety-relating and machine-technical installations are approved by
an expert before using them for the first time. The installations should be inspected every year by a skilled
person to be sure that safety is still optimal.
OPERATING INSTRUCTIONS

Do not switch the unit on and off in short time intervals

Always unplug the unit when it is not used for a longer time or before replacing the bulb or start servicing.

In the event of serious operating problems, stop using the fixture and contact your dealer immediately.

Important: Never look directly into the light source! Don’t use the effect in the presence of persons
suffering from epilepsy.
ENGLISH OPERATION MANUAL
JB SYSTEMS ® 4/26 ATOM
MAINTENANCE

Make sure the area below the installation place is free from unwanted persons during servicing.

Switch off the unit, unplug the mains cable and wait until the unit has been cooled down.
During inspection the following points should be checked:

All screws used for installing the device and any of its parts should be tightly fastened and may not be
corroded.

Housings, fixations and installations spots (ceiling, truss, suspensions) should be totally free from any
deformation.

When an optical lens is visibly damaged due to cracks or deep scratches, it must be replaced.

The mains cables must be in impeccable condition and should be replaced immediately when even a
small problem is detected.

In order to protect the device from overheat the cooling fans (if any) and ventilation openings should be
cleaned monthly.

The interior of the device should be cleaned annually using a vacuum cleaner or air-jet.

The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to
optimize light output. Cleaning frequency depends on the environment in which the fixture operates: damp,
smoky or particularly dirty surroundings can cause greater accumulation of dirt on the unit’s optics.

Clean with a soft cloth using normal glass cleaning products.

Always dry the parts carefully.

Clean the external optics at least once every 30 days.

Clean the internal optics at least every 90 days.
Attention: We strongly recommend internal cleaning to be carried out by qualified personnel!
SPECIFICATIONS
Mains Adapter: input: AC 100- 240V, 50/60Hz
Output: 15Vdc / 1,5A
Power consumption: 13 Watt
Sound Control: Internal microphone
Lamp: 120 LEDs (R=20, G=20, B=20, O=20, W=40)
Size: see drawing
Weight: 1,2 kg
Every information is subject to change without prior notice
You can download the latest version of this user manual on our website: www.beglec.com