4
IMPORTANT SAFETY INFORMATION
ELECTROMAGNETIC
COMPATIBILITY
This device complies with part 15 of the FCC Rules and the Product speci-
fications noted on the Declaration of Conformity. Operation is subject to the
following two conditions:
• This device may not cause harmful
interference, and
• This device must accept any interference received, including interfer-
ence that may cause undesired operation.
Operation of this unit within significant
electromagnetic fields should be avoided.
• Use only shielded interconnecting cables.
U.K. MAINS PLUG WARNING
A molded mains plug that has been cut off from the cord is unsafe.
Discard the mains plug at a suitable disposal facility. NEVER UNDER ANY
CIRCUMSTANCES SHOULD YOU INSERT A DAMAGED OR CUT MAINS PLUG
INTO A 13 AMP POWER SOCKET. Do not use the mains plug without the
fuse cover in place. Replacement fuse covers can be obtained from your
local retailer. Replacement fuses are 13 amps and MUST be ASTA approved
to BS1362.
FEDERAL COMMUNICATION
COMMISSION INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC CAUTION
Any changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that
may cause undesired operation.
IMPORTANT NOTE
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This transmitter module must not be colocated or operated
in conjunction with any other antenna or transmitter. This End equipment should be
installed and operated with a minimum distance of 20 centimeters between the radiator
and your body.
CANADA STATEMENT
This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject
to the following two conditions:
1. This device may not cause interference; and
2. This device must accept any interference, including interference that may cause
undesired operation of the device.
This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject
to the following two conditions:
1. l’appareil ne doit pas produire de brouillage;
2. l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi,même
si le brouillage est susceptible d’en compromettre le fonctionnement.
CAUTION EXPOSURE
This device meets the exemption from the routine evaluation limits in section 2.5 of
RSS102 and users can obtain Canadian information on RF exposure and compliance.
Le dispositif répond à l’exemption des limites d’évaluation de routine dans la section
2.5 de RSS102 et les utilisateurs peuvent obtenir des renseignements canadiens sur
l’exposition aux RF et le respect.
THE FINAL END PRODUCT MUST BE LABELLED IN
A VISIBLE AREA WITH THE FOLLOWING
The Industry Canada certification label of a module shall be clearly visible at all times
when installed in the host device, otherwise the host device must be labelled to display
the Industry Canada certification number of the module, preceded by the words
“Contains transmitter module”, or the word “Contains”, or similar wording expressing
the same meaning, as follows: “Contains transmitter module IC: 6132A-MB8811VMA”
This End equipment should be installed and operated with a minimum distance of 20
centimeters between the radiator and your body.
Cet équipement devrait être installé et actionné avec une distance minimum de 20
centimètres entre le radiateur et votre corps.
The end user manual shall include all required regulatory information/warning as shown
in this manual.
If you want to dispose this product, do not mix it with
general household waste. There is a separate collection
system for used electronic products in accordance with
legislation that requires proper treatment, recovery
and recycling.
Private household in the 25 member states of the EU, in Switzerland
and Norway may return their used electronic products free of charge
to designated collection facilities or to a retailer (if you purchase a
similar new one).
For Countries not mentioned above, please contact your local authori-
ties for a correct method of disposal.
By doing so you will ensure that your disposed product undergoes
the necessary treatment, recovery and recycling and thus prevent
potential negative effects on the environment and human health.
MAGNETIC FIELD
CAUTION! Do not locate sensitive high-gain equipment such as
preamplifiers or tape decks directly above or below the unit. Because this
amplifier has a high power density, it has a strong magnetic field which
can induce hum into unshielded devices that are located nearby. The field
is strongest just above and below the unit.
If an equipment rack is used, we recommend locating the amplifier(s)
in the bottom of the rack and the preamplifier or other sensitive equip-
ment at the top.
USE GROUNDED OUTLET ONLY!
Apparatet må tilkoples jordet stikkontakt
Apparaten skall anslutas till jordat uttag
Laite on liitettävä suojakoskettimilla varustettuun pistorasiaan
