background image

9

OPERATION

MIN        MAX

Subwoofer

Level

MIN        MAX

Subwoofer

Level

Move the Master Power
switch (marked “Power” 

¡

)

to the “•” (On) position to
use the subwoofer. The
SUB180 subwoofer will auto-
matically turn on or go into
standby (sleep) mode when
left in the auto mode (“Auto/

On” switch 

in the “Auto”

position). When your
receiver or amplifier is off, 
or is not sending program
material to the subwoofer,
the subwoofer will be in
standby mode (LED will be
red). When the subwoofer

senses an audio signal, it will
automatically turn on (LED
will be green). If the sub-
woofer does not sense a sig-
nal after approximately 20
minutes, it will automatically
go back into standby mode.

When the “Auto/On” switch

is switched to the “On”

position, the subwoofer will
remain on, whether or not
program material is playing.

If you will be away from
home for an extended period
of time, or if the subwoofer
will not be used, switch the
Master Power switch 

¡

to

the Off position.

VOLUME

POWER

SPEAKER LEVEL

SUBWOOFER

LEVEL

OUT

IN

L                        R

LINE LEVEL IN

LFE

L

R

AUTO              ON

MIN              MAX 

SUB180

£

¡

IMPORTANT: CONNECT STRIPED WIRE  TO RED (    ) SPEAKER TERMINAL.

GREEN: ON
RED: STANDBY

+

A Harman International Company

JBL, Incorporated

+           –           –           +

Volume may be adjusted
using the Subwoofer Level
control 

£

as shown.

SCS180.6 OM  7/21/04  12:38 PM  Page 9

Summary of Contents for SCS180.6













Reviews: