background image

INCLUDED

THANK YOU FOR CHOOSING JBL

For more than 60 years, JBL
has been involved in every
aspect of music and film
recording and reproduction,
from live performances to
the recordings you play in
your home, car or office.

We’re confident that the JBL

®

speaker you have chosen will
provide every note of enjoy-

ment that you expected –
and that when you think
about purchasing additional
audio equipment for your
home, car or office, you will
once again choose JBL.

Please take a moment to
register your product on our
Web site at www.jbl.com. 
It enables us to keep you

posted on our latest advance-
ments, and helps us to better
understand our customers
and build products that meet
their needs and expectations.

JBL, Inc.

One SCS SAT500, one SCS SAT300 
or one SCS SAT200 with wall-mount
bracket, shelf stand and floor stand
adapter.  

One 40' (12m) speaker cable.

In addition, there are two hardware
bags included. Hardware Bag A 
contains the metal tightening bar and
screw for the shelf stand. Hardware
Bag B contains screws for the floor
stand adapter and parts for the 
wall-mount bracket.

SCS SAT500

SCS SAT200

SCS SAT300

SURROUND CINEMA
SPEAKERS

OWNER’S GUIDE

®

SCS-SAT500,300,200 OM  4/25/07  11:39 AM  Page 3

Summary of Contents for SCS SAT500









Reviews: