JBL S412PII Owner'S Manual Download Page 8

S P E C I F I C A T I O N S

Maximum Recommended 

Amplifier Power:**

250W

Powered Subwoofer 

Amplifier Output:

200W

Nominal Impedance:

8 Ohms

Sensitivity (2.83V/1m):

92dB

Frequency Response (–3dB):

32Hz – 20kHz

Crossover Frequencies:

250Hz, 700Hz, 3500Hz

High-Frequency Transducer:

1" Pure-titanium dome, with rubber surround, shielded;
Elliptical Oblate Spheroidal™ (EOS) waveguide

Midrange Transducer:

4" PolyPlas™ (polymer-coated cellulose fiber) cone, rubber
surround, shielded; Linear Field Proximity™ (LFP) bezel

Midbass Transducer:

6" PolyPlas™ (polymer-coated cellulose fiber) cone, rubber
surround, shielded

Low-Frequency Transducer:

12" PolyPlas™ (polymer-coated cellulose fiber) cone,
rubber surround, SFG,™ magnetic shorting rings, high-temp
oversized Kapton

®

voice coil, HeatScape™ motor structure,

cast-aluminum basket, shielded

Dimensions (H x W x D):

44" x 14-3/4" x 16-1/16" (17" with grille)
1118mm x 375mm x 408mm (432mm with grille)

Weight (per speaker):

100 lb (45.5kg)

All features and specifications are subject to change without notice.

* Trademark of Dolby Laboratories. 

DTS is a registered trademark of Digital Theater Systems, Inc.

** The maximum recommended amplifier power rating will ensure proper system headroom to 

allow for occasional peaks.  We do not recommend sustained operation at these maximum 
power levels.

JBL Consumer Products

250 Crossways Park Drive, Woodbury, NY 11797

8500 Balboa Boulevard, Northridge, CA 91329

800-336-4JBL (4525) (USA only)  

www.jbl.com 

©2001 JBL, Incorporated

JBL is a registered trademark of JBL, Incorporated.

Part No. 338047-001

T W E E T E R   T Y P E :

Pure-titanium dome with EOS™ waveguide

D E S I G N   G O A L :

Bring the thrill of live performance and movie sound to

the home environment by calling on JBL’s professional engineering leadership.

C R O S S O V E R   N E T W O R K :

Straight-Line Signal Path™ (SSP)

W O O F E R   T Y P E :

Cast-aluminum basket with HeatScape™ motor structure

P O R T   D E S I G N :

FreeFlow™ flared

P R O F E S S I O N A L   R E F E R E N C E :

Studio Monitor

O W N E R ’ S   G U I D E

P R O   S O U N D  
C O M E S   H O M E

P R O D U C T L I N E :

STUDIO

SERIES

M O D E L

S412P

II

N U M B E R :

Summary of Contents for S412PII









Reviews: