15
Features
1. SYSTEM EQ LED
– This light indicates BOOST
35;: 35;:RQO\RU021,725
35;: 35;:RQO\
2. SYSTEM EQ Button
a. Normal and Boost
(PRX825W and PRX835W
RQO\±'HIDXOWOLJKWRIILV1250$/
frequency response is linear and unaltered.
When light indicator is on, BOOST is selected
and internal equalization is applied to enhance
low frequency and high frequency response.
b. Main and Monitor
35;: 35;:
RQO\±6SHDNHULVRSWLPL]HGIRU0$,1SRVLWLRQ
when light is off, and MONITOR when the light
indicator is on.
NOTE:
This button is also used to Factory Reset
speaker settings. See
“FACTORY RESETS” on
page 19
for more information.
3. FRONT LED Button
– This push button allows
you to turn on/off the Power LED on the front of
the speaker.
4. LIMIT
Indicator
– There is one YELLOW LED
indicator that will illuminate when input clipping
occurs or peak output has been reached and the
DSP limiter is acting.
5. GAIN
Knobs
– These gain knobs are for setting
the input level of CH1 and CH2.
6. SIGNAL
Indicator
– There are two LED indicators
RQHIRUHDFKFKDQQHOWKDWZLOOLOOXPLQDWH*5((1
when signal is present at the input connector.
7. MIC
LED
– This light indicates MIC input level is
selected for the channel.
8. MIC SELECT Button
– Speaker is in LINE level
mode by default. Press and hold the button for 2
seconds to change to MIC level. Light indicator will
turn on while in MIC level input.
9. XLR
Inputs
– Female balanced XLR and 1/4 inch
phone jack combo input connectors.
10. RCA SIGNAL LED
– This light indicates RCA input
signal.
11. RCA Inputs
– Female unbalanced RCA input
connectors.
12. WI-FI LINK LED
– This LED has four states:
a. Off
– The speaker is not connected to WI-FI.
b. On
– The speaker is connected to WI-FI.
c. Blinking
Slowly
– The speaker is in Access
Point mode and has not yet established a WI-
FI connection.
d. Blinking
Rapidly
– The speaker is in Access
Point mode and is communicating with a
connected device.
13. WI-FI CONNECT Button
– This button is used
to connect to a WI-FI network for speaker
FRQ¿JXUDWLRQDQGFRQWUROXVLQJWKH35;&RQQHFW
application. This button has two functions:
a. Press and release
– Instructs the speaker to
WU\FRQQHFWLQJWRWKHFRQ¿JXUHG:,),QHWZRUN
b. Press and hold for 2 seconds
– Switches
between “Access Point” and “Normal” network
operating modes. By default, the speaker is in
“Normal” network operating mode. Switching
to Access Point mode allows all PRX800W
VSHDNHUVLQDV\VWHPWREHLQLWLDOO\FRQ¿JXUHG
for your network router. When switched to
Access Point mode, the WI-FI LINK LED will
ÀDVKVORZO\
For more information on using WI-FI, see
“WI-FI
SETUP” on page 18
.
14. 50/50 MIX LED
– This light indicates a 50/50 mix
going to the MIX OUT connector.
15. 50/50 MIX Button
– This button determines how
the inputs are sent to the MIX OUT connector.
When disengaged (50/50 LED off, this is the
GHIDXOWDWUXHPL[EDVHGRQKRZWKHJDLQVDUH
set between CH1 and CH2 will be sent to the MIX
287FRQQHFWRU:KHQHQJDJHG/('RQD
50/50 mix of CH1 and CH2 will be sent to the MIX
OUT connector. This button must be pressed and
held for 2 seconds to switch between options.
16. MIX OUT Connector
– Male balanced XLR output
connector. This connector provides a full-range
signal which can be daisy chained to another
speaker.
17. REMOTE EQ LED
– Indicates the speaker has
settings applied by the WI-FI application.
18. POWER LED
– This LED illuminates when the
“Power Switch” has been turned to the on position.
It will illuminate BLUE when the system has power
and is ready to pass audio.
