7
Controls
1. POWER ON/OFF button (1)
2. SELECT button (2)
2-1 Audio control ( VOLUME / BASS / TREBLE / BALANCE / FADER )
a. BASS Control
b. TREBLE Control
c. BALANCE Control
d. FADER Control
Simply press the Power button (1) to turn the unit on and off.
If the key or one of the
keys is not pressed within 5 seconds, the radio automatically switches into volume
control mode.
To adjust the bass tone level, first select the bass mode by pressing button (2) until BASS
appears on the display panel. Turn VOL knob (2) within 5 seconds to adjust the bass level
as desired. The bass level will be shown on the display panel from a minimum of BASS -7
to a maximum of BASS +7
To adjust the treble tone level, first select the treble mode by pressing button (2) until
TREBLE appears on the display panel. Turn VOL knob (2) within 5 seconds to adjust
the treble level as desired. The treble level will be shown on the display panel from a
minimum of TREBLE -7 to a maximum of 7
To adjust the left-right speaker balance, first select the balance mode by pressing button
(2) until BALANCE appears on the display panel. Turn VOL knob (2) within 5 seconds
to adjust the left-rear speaker level as desired. The balance position will be shown by the
bars on the display panel from BALANCE L10 (full left) to BALANCE R10 (full right).
To adjust the front-rear speaker balance, first select the fader mode by pressing button (2)
until FADER appears on the display panel. Turn VOL knob (2) within 5 seconds to adjust
the front-rear speaker level as desired. The fader position will be shown by the bars on the
display panel from FADER F10 (full front) to FADER R10 (full rear).
Press SEL button (2) repeatedly to select the desired mode in the following order:
At each feature, turn VOL knob (2) to adjust to the desired level.
.
.
BASS --> TREBLE --> BALANCE --> FADER
10
Operating the Radio
1. Radio Operation
2. To Select Band
3. Auto / Manual tuning button (7)
4. Manual Station store
5. A.PS - Auto Store function (16)
6. SCAN function (15)
Press MODE button (3) to select Radio mode. Station frequency is indicated on display.
Press BD/LD button (6) to toggle through radio modes as follows:
FM1 --> FM2 --> FM3 --> AM1 --> AM2 --> FM1.
Simply press TUNE up/down button (7) to activate the Auto Tune mode. It will automatically
tune up or down the wave band and stop at the next station of sufficient signal strength.
Press and hold TUNE button (7) to enter manual tuning mode. It would display MANU on
the LCD, then simply press TUNE up/down button (7) to tune a station by step. The unit will
revert back to Auto Tune mode after 5 seconds without use.
Select the desired band and tune to a radio station to be memorized. Choose the preset
button memory location span 1-6 into which the station is to be stored and press and
hold that preset button for 2 seconds.
The station will now be entered into the preset memory. 6 stations can be memorized
on each of the FM1, FM2, FM3, AM1, AM2 bands.
In Radio mode, press A.PS button (16) to scan the preset stations in each band. It would
play each preset station for about 5 seconds. At the desired station press A.PS button
again to stop scanning.
Press and hold A.PS button (16) for approximately 2 seconds until you hear a beep which
confirms the memory function is engaged. The unit will SEARCH for six strong stations
and automatically store them on buttons 1 - 6. (FM/AM only)
You can override the preset station on any button by manually setting a new frequency.
In Radio mode, press the SCAN button to scan strong stations. At desired station press the
SCAN button again to stop scanning.
5
2
7
4
6 8
10
11
12
13
14
1
3
15
9
16
17
5
2
7
4
6 8
10
11
12
13
14
1
3
15
9
16
17
