JBL MPA1100 Owner'S Manual Download Page 2

1

Rack Mounting Precautions

To avoid damage to the amplifier mounting ears

and/or rack rails, the amplifier must be supported at all
four corners when used in portable racks. 

Consult JBL Service Dept for availability of Rear

Support Brackets. 

Lifting Precautions

In order to safely move or install the amplifier, it is

recommended that two persons share the weight when
lifting and positioning the unit.

Sicherheitsvorschriften für den Einbau in ein Gestell

Um Schäden auf den Befestigungsleisten des

Verstärkers und/oder den Gestellschienen zu vermei-
den, muß der Verstärker beim Einbau in ein trag-
bares Gestell an allen vier Ecken gestützt werden.

Erkundigen Sie sich bei der JBL-

Kundendienstabteilung nach Stützen für die
Rückseite des Verstärkers.

Sicherheitsvorschriften beim Hochheben

Um den Verstärker sicher zu verschieben oder

einzubauen, wird empfohlen, das Gewicht des
Verstärkers beim Hochheben und Verschieben gleich-
mäßig auf zwei Personen zu verteilen.

Cautions Sicherheitsvorschriften

WARNUNG:

ZUR VERMEIDUNG VON FEUER ODER

ELEKTRISCHEN SCHLÄGEN DAS GERÄT NICH MIT REGEN
ODER FEUCHTIGKEIT IN BERÜHRUNG BRINGEN

.

WARNING: 

TO P R E V E N T F I R E O R E L E C T R I C

SHOCK

DO NOT EXPOSE THIS EQUIPMENT TO RAIN

OR MOISTURE

.

Erklärung der graphischen Symbole

Der Blitz mit nach unten zeigendem Pfeil in einem gleichseitigen
Dreieck weist den Benutzer auf das Vorhandensein einer
unisolierten, “gefährlichen Spannung” im Gehäuse hin, die stark
genug sein kann, einer Person einen elektrischen Schlag zu ver-
setzen.

Das Ausrufezeichen in einem gleichseitigen Dreieck weist den
Benutzer auf nichtige Betriebs - und Wartungsvorschriften in den
Beiliegenden Unterlagen des Gerätes hin.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: T

O

R

EDUCE THE RISK OF ELECTRIC

SHOCK

DO NOT REMOVE THE COVER

. N

O USER

-

SERVICEABLE PARTS INSIDE

. R

EFER SERVICING TO

QUALIFIED SERVICE PERSONNEL

.

VORSICHT: 

UM DAS RISIKO EINES ELEKTRISCHEN

S C H L A G E S Z U V E R M I N D E R N

A B D E C K U N G N I C H T

ENTFERNEN

KEINE BENUTZER BEDIENUNGSTEILE IM

INNERN

BEDIENUNG NUR DURCH QUALIFIZIERTES

BEDIENUNGSPERSONAL

.

To reiterate the above warnings: servicing instruc-

tions are for use by qualified personnel only. To avoid
electric shock, do not perform any servicing other than
that contained in the Operation Instructions unless you
are qualified to do so. Refer all servicing to qualified
service personnel

CAUTION

RISK OF ELECTRIC SHOCK:

OPEN ONLY IF QUALIFIED

AS SERVICE PERSONNEL

Eindrigliche Warnung: Wartungsvorschriften dienen

nur der Benutzung durch qualifiziertes Personal. Zur
Vermeidung eines elektrischen Schlages keine anderen
als die in den Betriebsvorschriften beschriebenen
Wartungsarbeiten ausführen, es sei denn, Sie sind dafür
qualifiziert. Wartungsarbeiten sind von qualifiziertem
Wartungspersonal auszuführen.

Explanation of Graphical Symbols

The lightning flash with arrowhead symbol, within an equi-
lateral triangle, is intended to alert the user to the presence
of uninsulated “dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude to constitute
a risk of electric shock to humans.

The exclamation point within an equilateral triangle is
intended to alert the users to the presence of important
operating and maintenance (servicing) instructions in the
literature accompanying the product.

V O R S I C H T

GEFAHR EINES ELEKTRISCHEN

SCHLAGES NICHT ÖFFNEN

V O R S I C H T

GEFAHR EINES ELEKTRISCHEN SCHLAGES: NUR VON

QUALIFIZIERTEM WARTUNGSPERSONAL ZU ÖFFNEN

V O R S I C H T

UM ELEKTRISCHEN SCHLAG ZU VERMEIDEN, KEINE

FINGERN ODER GEGENSTÄNDE IN ÖFFNUNGEN DES

GEHÄUSES STECKEN.

C A U T I O N

TO AVOID ELECTRIC SHOCK, DO NOT INSERT FINGERS

OR OBJECTS INTO ANY OPENINGS IN THE CABINET.

Summary of Contents for MPA1100
























Reviews: