Power On
Plug your subwoofer’s AC cord into a wall outlet. Do not use the
outlets on the back of the receiver.
Initially set the Subwoofer-Level Control
2
to the “min” position.
Turn on your sub by pressing the Power Switch
5
on the rear panel.
Turn on your entire audio system and start a CD or movie soundtrack
at a moderate level.
Auto On/Standby
With the Power Switch
5
in the ON position, the Status LED on the
top will remain lit in red or green to indicate the On/Standby mode of
the subwoofer.
RED = STANDBY (No signal detected, Amp Off)
GREEN = ON (Signal detected, Amp On)
The subwoofer will automatically enter the Standby mode after
approximately 10 minutes when no signal is detected from your
system. The subwoofer will then power ON instantly when a signal is
detected. During periods of normal use, the Power Switch
5
can be
left on. You may turn off the Power Switch
5
for extended periods
of nonoperation, e.g., when you are away on vacation.
Adjust Gain
Turn your Subwoofer-Level Control
2
up to the halfway position. If
no sound emanates from the subwoofer, check the AC-line cord and
input cables. Are the connectors on the cables making proper
contact? Is the AC plug connected to a “live” receptacle? Has the
Power Switch
5
been pressed to the “On” position? Once you have
confirmed that the subwoofer is active, proceed by playing a CD,
record or cassette. Use a selection that has ample bass information.
Set the overall volume control of the preamplifier or stereo to a
comfortable level. Adjust the Subwoofer-Level Control
2
until you
obtain a pleasing blend of bass. Bass response should not over-
power the room but rather be adjusted so there is a harmonious
blend across the entire musical range. Many users have a tendency
to set the subwoofer volume too loud, adhering to the belief that a
subwoofer is there to produce lots of bass. This is not entirely true.
A subwoofer is there to enhance bass, extending the response of the
entire system so the bass can be felt as well as heard. However,
overall balance must be maintained or the music will not sound
natural. An experienced listener will set the volume of the subwoofer
so its impact on bass response is always there but never obtrusive.
Phase Control
The Phase Switch
0
determines whether the subwoofer speaker’s
pistonlike action moves in and out with the main speakers, 0˚, or
opposite the main speakers, 180˚. Proper phase adjustment depends
on several variables such as room size, subwoofer placement and
listener position. Adjust the phase switch to maximize bass output at
the listening position.
Crossover Adjustment
The Crossover Adjustment Control
3
determines the highest
frequency at which the subwoofer reproduces sounds. If your main
speakers can comfortably reproduce some low-frequency sounds,
set this control to a lower frequency setting, between 50Hz and
100Hz. This will concentrate the subwoofer’s efforts on the ultradeep
bass sounds required by today’s films and music.
If you are using smaller bookshelf speakers that do not extend to the
lower bass frequencies, set the Crossover Adjustment control to a
higher setting, between 120Hz and 150Hz.
NOTE:
This control will have no effect if the LFE/Normal Selector
1
is set to LFE. If you have a Dolby Digital or DTS processor/receiver,
the Low-Pass Frequency is set by the processor/receiver. Consult
your owner’s manual to learn how to view or change this setting.
The enclosure may be cleaned using a soft cloth to remove finger-
prints or to wipe off dust.
The grille may be gently vacuumed. Stains may be removed with an
aerosol cleaner, following its instructions. Do not use any solvents
on the grille.
All wiring connections should be inspected and cleaned or remade
periodically. The frequency of maintenance depends on the metals
involved in the connections, atmospheric conditions and other
factors, but once per year is the minimum.
If a problem occurs, make sure that all connections are properly
made and clean. If a problem exists in one loudspeaker, reverse the
connection wires to the left and right system. If the problem remains
in the same speaker, then the fault is with the loudspeaker. If the
problem appears in the opposite speaker, the cause is in another
component or cable. In the event that your subwoofer ever needs
service, contact your local JBL dealer or distributor, or visit
www.jbl.com for a service center near you.
OPERATION
6
MAINTENANCE AND SERVICE
33346_JBL ES150_250P_ENG 14/06/07 11:14 Side 6
