background image

The 

4344MkII

loudspeaker systems have an oiled finish. Cleaning

should be done with an untreated dust cloth. Do not use conventional 

furniture waxes and polishes, which are not designed for oiled finishes. 

If touch-up is necessary or the finish appears to be drying out, the surface

may be re-oiled with a commercially available oil-finishing preparation.

Do not use any solvents on the finish.

The grille may be gently vacuumed. Stains may be removed with an aerosol

cleaner, following the cleaner's instructions. Do not use any solvents on the

grille.

All wiring connections should be inspected and cleaned or remade 

periodically. The frequency of maintenance depends on the metals involved

in the connections, atmospheric conditions, and other factors, but once per

year is the minimum. The battery should be replaced approximately every

three years. Consult your JBL dealer for specific recommendations.

If a problem occurs, make sure that all connections are properly made and

clean. If a problem exists in one loudspeaker, reverse the speaker wires to

the left and right system. If the problem remains in the same speaker, then

the fault is with the loudspeaker. If the problem appears in the opposite

speaker, the cause is in another component or cable. In the event that your

4344MkII

loudspeaker system ever needs service, contact your local

JBL dealer. 

Maintenance and Service

No.

13

4344 MK 11 Manual  7/21/98 3:18 PM  Page 12

Summary of Contents for 4344 MKII















Reviews: