ENGLISH
OPERATION MANUAL
JB SYSTEMS
®
3/26
LED STROBE
DESCRIPTION:
1.
Optical lens
2.
Hanging bracket with 2 knobs on both sides to fasten the unit and a mounting hole to fix a mounting hook.
3.
15Vdc input, connect the supplied AC/DC-mains adapter here.
4.
MODE SELECTOR knob:
a) BURST-8 MODE: the unit shows burst of 8 flashes, followed by a time interval that can be adjusted
with knob (5)
b) BURST-4 MODE: the unit shows burst of 4 flashes, followed by a time interval that can be adjusted
with knob (5)
c) NORMAL STROBE MODE: normal strobe function, use knob(5) to adjust the speed.
d) MUSIC STROBE MODE: strobe works to the rhythm of the music, use knob(5) to adjust the mic
sensitivity.
5.
SPEED/SENSITIVITY knob: functionality depends on the working mode:
In burst mode you can adjust the time interval between two bursts.
In normal mode you can adjust the strobe speed from 0,5Hz to 20Hz
In Music mode you can adjust the sensitivity of the internal mic.
OVERHEAD RIGGING
Important: The installation must be carried out by qualified service personal only. Improper
installation can result in serious injuries and/or damage to property. Overhead rigging requires
extensive experience! Working load limits should be respected, certified installation materials
should be used, the installed device should be inspected regularly for safety.
Make sure the area below the installation place is free from unwanted persons during rigging, de-rigging
and servicing.
Locate the fixture in a well ventilated spot, far away from any flammable materials and/or liquids.
The device should be installed out of reach of people and outside areas where persons may walk by or be
seated.
Before rigging make sure that the installation area can hold a minimum point load of 10times the device’s
weight.
Always use a certified safety cable that can hold 12times the weight of the device when installing the unit.
This secondary safety attachment should be installed in a way that no part of the installation can drop
more than 20cm if the main attachment fails.
The device should be well fixed; a free-swinging mounting is dangerous and may not be considered!
Don’t cover any ventilation openings as this may result in overheating.
The operator has to make sure that the safety-relating and machine-technical installations are approved by
an expert before using them for the first time. The installations should be inspected every year by a skilled
person to be sure that safety is still optimal.
ENGLISH
OPERATION MANUAL
JB SYSTEMS
®
4/26
LED STROBE
OPERATING INSTRUCTIONS
Once connected to the mains the device starts running.
Do not switch the unit on and off in short time intervals
Always unplug the unit when it is not used for a longer time or before replacing the bulb or start servicing.
In the event of serious operating problems, stop using the fixture and contact your dealer immediately.
Important:
Never look directly into the light source! Don’t use the effect in the presence of persons
suffering from epilepsy.
MAINTENANCE
Make sure the area below the installation place is free from unwanted persons during servicing.
Switch off the unit, unplug the mains cable and wait until the unit has been cooled down.
During inspection the following points should be checked:
All screws used for installing the device and any of its parts should be tightly fastened and may not be
corroded.
Housings, fixations and installations spots (ceiling, truss, suspensions) should be totally free from any
deformation.
When an optical lens is visibly damaged due to cracks or deep scratches, it must be replaced.
The mains cables must be in impeccable condition and should be replaced immediately when even a
small problem is detected.
In order to protect the device from overheat the cooling fans (if any) and ventilation openings should be
cleaned monthly.
The interior of the device should be cleaned annually using a vacuum cleaner or air-jet.
The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to
optimize light output. Cleaning frequency depends on the environment in which the fixture operates: damp,
smoky or particularly dirty surroundings can cause greater accumulation of dirt on the unit’s optics.
Clean with a soft cloth using normal glass cleaning products.
Always dry the parts carefully.
Clean the external optics at least once every 30 days.
Clean the internal optics at least every 90 days.
Attention: We strongly recommend internal cleaning to be carried out by qualified personnel!
SPECIFICATIONS
Mains Adapter:
input: AC 100- 240V, 50/60Hz
Output: 15Vdc / 700mA
Power consumption:
5 Watt
Sound Control:
Internal microphone
Lamp:
68 white LEDs
Size:
see drawing
Weight:
0,5 kg
Every information is subject to change without prior notice
You can download the latest version of this user manual on our website: www.beglec.com
