background image

EN/2009.V01

 

WK-6221S

 

EN 

9.  Some material contains chemicals which may be toxic. Take caution to prevent dust inhalation 

and skin contact. Follow material supplier safety data. 

 

SAVE THESE INSTRUCTIONS! 

WARNING: 

DO NOT let comfort or familiarity with product (gained from repeated use) replace strict adherence to 
safety rules for the subject product. MISUSE or failure to follow the safety rules stated in this 
instruction manual may cause serious personal injury. 
 

SYMBOLS 

The followings show the symbols used for tool. 

 

Volts 

 

Direct current 

 

No load speed 

 

 

Revolutions or reciprocation per 

minute 

 

IMPORTANT SAFETY INSTRUCTIONS 

FOR BATTERY CARTRIDGE 

1.  Before using battery cartridge, read all instructions and cautionary markings on (1) battery 

charger, (2) battery, and (3) product using battery. 

2.  Do not disassemble battery cartridge. 

3.  If operating time has become excessively shorter, stop operating immediately. It may result in a 

risk of overheating, possible burns and even an explosion. 

4.  If electrolyte gets into your eyes, rinse them out with clear water and seek medical attention right 

away. It may result in loss of your eyesight. 

5.  Do not short the battery cartridge: 

1)  Do not touch the terminals with any conductive material. 
2)  Avoid storing battery cartridge in a container with other metal objects such as nails, coins, 

etc. 

3)  Do not expose battery cartridge to water or rain. A battery short can cause a large current 

flow, overheating, possible burns and even a breakdown. 

6.  Do not store the tool and battery cartridge in locations where the temperature may reach or 

exceed 50° C (122° F). 

7.  Do not incinerate the battery cartridge even if it is severely damaged or is completely worn out. 

The battery cartridge can explode in a fire. 

8.  Be careful not to drop or strike battery. 

Summary of Contents for WK-6221S
















Reviews: