manualshive.com logo in svg

Jay electronique Orion OREL, Installation And User Technical Manual

Share
Download
Jay electronique Orion OREL Installation And User Technical Manual Download Page 48

- 104 -

Orion

  -  324501H

FR

DE

EN

If the above requirements cannot be observed (case of ORRD receiver 
installed in cabinet), an external antenna must be used with extension 
(BNC connection). External antenna and extension must be ordered 
separately, see chapter 

Receiver accessories

.

For the 

ORRS

 and 

ORRA

 receivers, use of an external antenna requires 

that the user purchases and installs the plug-in antenna kit, reference : 

OWR01

. see kit installation in 

appendix E

.

Type of receiver installation

(with plug-in antenna)

Reference suggestion of antenna and extension to be used

Outside installation

Antenna 

VUB084

 or antenna 

VUB086

(possible use of extension with support 

VUB105/VUB125/VUB131

)

Installation on vehicle

Antenna 

VUB084

 + extension with support 

VUB105/VUB125/VUB131

or antenna 

VUB086

 + extension with support 

VUB105/VUB125/VUB131

Installation in plastic cabinet

ORRA

 and 

ORRS

 : antenna 

VUB084

 or antenna 

VUB086

ORRD

 : antenna 

VUB084

 + 90° BNC bend 

VUB060

Installation in metal cabinet

Antenna 

VUB084

 + extension 0,5m 

VUB170

or antenna 

VUB086

 + extension 0,5m 

VUB170

DRAFT a

Summary of Contents for Orion OREL



































































Reviews:

No comments

Brands by name

Popular brands

Load more brands