background image

12                                                                                                                                                                             

www.javad.com

Figure 13.  Ports tab

Parameter

Base

Rover

Input

-

The same correction type as 

Base has

Output

Select the correction type. -

Period (sec)

Set the period of 

correction output 

-

Baud rate

Baud rate for the corresponding receiver port

RTS/CTS

Enable

10. Open Advanced tab, and then Multipath Reduction 

subtab. Activate Code multipath reduction (mpnew) on 

base and rover for DGPS mode. 

For RTK mode activate Carrier multipath reduction 

(mpnew) as well (mpnew).

Figure 14.  Multipath Reduction

 11. Click Apply, to save the made changes and set-

tings into receiver’s memory and close the dialog win-

dow. The receiver configuration will be kept in the re

-

ceiver till you will change them or will  clear NVRAM. 

Note: 

For detailed description of settings and parameters see 

NetView Software Manual..

TriPad Configuration

The DELTA-3N’s simple user interface (TriPad) con-

sists of two keys (Power and Record) and two LEDs 

that control and display the receiver’s operation. 

Note: 

Use NetView to configure TriPad settings. Refer to the 

NetView Software Manual for all possible MinPad configurations.

Connect the receiver and PC as described above. 

Start NetView. Establish connection with the receiver. 

Open 

TriPad 

tab. Set the following parameters and 

click 

Apply

:

• “File a, File b”

• “Function Key” 

• “Automatic File Rotation Mode (AFRM)” 

File a, File b

In the fields File a, File b can be specified current 

log-file name, message output period, etc. 

• 

Current log-file edit box allows the user to specify 

the prefix of the log file, which will be saved into 

receiver memory during survey.

• In the Output Epochs Counter box the number of 

outputted epochs is shown.

• In the Implicit Message Output Period edit box the 

output period for the implicit messages can be spec-

ified. This parameter specifies the interval of output

-

ting messages into the log-file when data logging is 

activated with the TriPad or through the AFRM.

• Elevation Mask for Measurements Output (the 

minimum elevation angle for the satellites whose 

data  will  be  put  in  the  receiver  files  logged  when 

pressing FN). 

• Satellites Number Mask for Position computation 

- Satellites with elevations lower than this mask will 

be excluded from position computation.

• 

File Name Prefix - this setting specifies what prefix 

will be added to the names of the receiver files creat

-

ed via MinPad, (i.e., by pressing FN). The prefix can 

be up to 20 characters long. Default is log.

• 

Enable Implicit Management of Specific - enables/

disables the management of Implicit Message Out-

put Period.

Function Key

Figure 15.  Funktion Key

Summary of Contents for DELTA-3N























Reviews: