background image

 

1. Mechanical/Electrical/Illustration of Working Principle data 

Electrical Data 

 

 

 

 

 

 

 

 

 

SN——

Series number

 

CE

EN

ISO——

Certification standards

 

Uin—— 

rated supply voltage 

U20——

range of rated ac no-load voltage and number of adjustable steps

 

I1

max

——

max input welding current

 

I2

max

——

max output welding current

 

Duty——

Duty cycle

 

Weight——

weight of the welding equipment 

 

 

2. CD stud mode 

2-1. Summary 

The machine is for Capacitor Discharge Stud Welding ,the weld able range is Ø3- Ø8mm. Stud materials are soft 

steel, stainless steel, aluminum, titanium (Ti), brass and copper screw. Stud Welding time is about 

3/1000s-6/1000s,the time is very short, so the welding heat can not damage the base metal, even the base metal is 

sheet metal. 

 

2-2. Matters need attention 

(1) Input power is AC110 / AC220 / AC380≥15A 

(2) Turn "off " the switch, when not use the machine. 

(3) Make sure turn "off " the switch, when connect or remove the cables of the machine. 

(4) The machine maintenance and repair must turn "off " the switch after 5 minutes. 

(5) The stud clamp is inside the stud welding torch. The inside diameter of stud clamp must suitable the stud screw. 

Do not use worn stud clamp. 

(6) Stud welding may to cause welding arc and metal spatter, protect your self with appropriate safety garments 

and goggles. 

(7) Make sure there are no flammable materials work area. 

(8) The machine must use special stud screw, so must use original spares. 

(9) Pleases contact the manufacturer ,as following situations:mechanical failure, reduce or increase the torch cable, 

change the standard equipment. 

 

MODE

Summary of Contents for 11244-X














Reviews: