Jason International, Inc. •
501.771.4477
Page 7 of 9
Customer Service : 800.255.5766
USER MAINTENANCE INSTRUCTIONS
SURFACE MAINTENANCE
Areas with minor scratches or dull surfaces can be restored
by applying commercially available plastic polish (i.e. Novus
Plastic Polish No. 2, available at your Jason dealer), followed
by an application of acrylic paste wax. Buff the surface with a
clean soft cloth. Do not use sandpaper, steel wool, or abrasive
rubbing compounds.
If scratches are too deep to rub out, or if the damage penetrates
the acrylic surface, consult your dealer for recommendations
on surface repair.
FLUSHING / SANITIZING
Upon start-up and not to exceed 90 days thereafter, flush
the Whirlpool bath and plumbing system
with
Jason’s
Bath System Cleaner, available at Jason Dealers, or use an
equivalent cleaner. Follow the cleaning instructions below:
1. Close the bath drain and open the air controls.
2. Fill the bath with warm water to a level at least 2” (5 cm)
above the highest jet.
3. Pour 16 ounces of Jason’s Bath System Cleaner into the
bath water.
4. Turn on the whirlpool pump for 10 minutes.
5. Turn off the pump and drain the bath.
6. To rinse, refill the bath with cold water, turn on the pump
for five minutes, then turn off the pump and drain the
bath.
Note:
The bath can be sanitized after each bather without
harming the whirlpool bath plumbing.
REPAIR
Refer all plumbing or electrical repair to a qualified service
technician.
DO NOT ATTEMPT TO RESOLVE THE
PROBLEM.
T
his can result in danger of electrical shock
or damage to the unit and will VOID THE WARRANTY.
Remember, when contacting your dealer or service
representative, always have your serial number, proof of
purchase, and model number. This will insure a quick response
on warranty items. The serial number can be found on the
front page of this manual or on the small card adhered to the
back of the bath just above the pump.
ALL WARRANTY REPAIRS MUST BE AUTHORIZED BY
THE MANUFACTURER BEFORE WORK IS STARTED.
HUMIDITY
Warning: Avoid high humidity levels in your home.
Mold, mildew, fungi and bacteria which may be harmful
to health thrive in areas with continued high humidity
levels; therefore, every precaution should be taken to
make sure your plumbing fixtures including bathtubs,
therapy baths, or showers do not become a source of
high humidity due to improper installations or leaks.
To avoid having your plumbing fixtures become a source of
unwanted humidity, please make sure the following steps are
taken prior to installation.
1. Make sure the area where the bathtub or shower is
installed is well vented and allows enough ventilation and
air circulation to dry the bathroom environment within a
short time after taking a bath or shower.
2. If your bath or shower unit is tiled-in, use units with an
integral tile flange or make sure a tile flange kit or a similar
mechanical barrier is installed to prevent shower spray,
splash, or overflow to leak behind the bathtub.
3. Make sure the plumber properly tests your therapy bath
before it is roughed in to make sure there are no leaks and
it is installed with proper access to bath equipment.
4. Make sure that all the plumbing and fixtures in the bathroom
are in good working order and have no leaks.
5. Do not use carpeting or other materials or furniture, which
can hold moisture in your bathroom.
6. Use disinfectant to clean any bathroom surfaces which
are regularly exposed to moisture.
7. Clean and disinfect humidifier and dehumidifiers as
recommended by the manufacturer. Replace the air filter
on the HVAC unit once a month.
8. Clean moldy surfaces as soon as any mold appears by using
a detergent/soapy solution and appropriate household
cleaner. Always use gloves during cleaning. Dispose of
any sponges or rags used to clean mold.
CLEANING
With minimum care, your acrylic-surfaced bath will retain its
high-luster finish for many years. For regular cleaning use
Jason Bath Cleaner or a mild
NONABRASIVE
liquid detergent
solution (i.e. glass cleaner) and a soft, wet cloth or sponge.
Do not run the air system with foaming cleaners or soaps.
Rinse the bath thoroughly after cleaning.
