specifications, installation,
operation and maintenance instructions
Model SER- 03
page 6 of 8
JARVIS
6205015:
PRODUCTS CORPORATION
33 ANDERSON ROAD, MIDDLETOWN, CONNECTICUT 06457- 4926
UNITED STATES OF AMERICA E- MAIL.
TEL. 860- 347- 7271 FAX. 860- 347- 6978 WWW. j
arvisproducts.com
SPECIFICATIONS
Motor Power
1.4 hp
1050 W
Operating Volt/Amp 115V/10.3A, 1 phase, 50/60 Hz
230V/4.9A, 1 phase, 50/60 Hz
Stroke
1.57 in
40 mm
Blade Speed
6500 strokes / min
Control Handle
Single
Electric
Blade Length
8 in
203 mm
16 in
406 mm
Overall Length (w/o blade)
20.5 in
521 mm
Weight (w/o blade)
18.6 lbs
8.4 kg
Vibration
135 dB Front 137.5 dB Rear
5.6 m/sec
2
7.5 m/sec
2
Noise (one meter from tool)
93.5 dbA
INSTALLATION INSTRUCTIONS
ALL WIRING MUST BE DONE IN ACCORDANCE
WITH NATIONAL, STATE AND LOCAL ELEC-
TRICAL CODES.
1 Install the saw above the work station from a balanc-
er if desired.
Jarvis
part number 4042045 is avail-
able.
2 Plug the 115 V, 50/60 Hz model into a standard 115
V wall outlet. Plug the 230 V, 50/60 Hz model into
a standard 230 V wall outlet.
OPERATION INSTRUCTIONS
1
Test
the tool prior to use.
Depress
the trigger and the
tool should start.
Release
the trigger and the tool
should stop.
If the tool malfunctions, remove it from ser-
vice and report the problem to your supervi-
sor immediately.
2 Make sure that the saw moves freely on the balancer.
3 Making the cut.
3.1 Position the saw.
3.2 Depress the trigger to start the saw and make the
cut.
3.3 When the desired length of cut is reached, re-
lease the trigger. This will stop the blade from
oscillating.
Continue holding the saw firmly with both
hands until the blade stops oscillating.
3.4 Withdraw the saw blade from the carcass.
MAINTENANCE INSTRUCTIONS
ALWAYS DISCONNECT THE POWER SUPPLY IN
ACCORDANCE WITH OSHA’S LOCKOUT/TAG-
OUT PROCEDURES (29 CFR 1910.147) BEFORE
INSTALLING OR REMOVING A BLADE, OR BE-
FORE PERFORMING ANY REPAIRS OR MAINTE-
NANCE.
1 MONTHLY:
1.1 Remove eight (8) flat head screws (item 31),
eight (8) serrated lock washers (item 32), crank-
case cover (item 26) and gasket (item 25).
1.2 Ensure that crankcase (item 15) is 3/4 full of
food grade grease (NLGI- 2).
Jarvis
part num-
ber 1062003 is available. Add grease if neces-
sary.
1.3 Replace gasket, bottom cover, washers and
screws.
1.4 If more frequent lubrication is desired, grease
can be added through plug (item 30) or grease
fitting (item 18).
1.5 Drive pins (items 10 and 40) can also be lubric-
ated without removing the crankcase cover
(item 26). Remove plug (item 30). With drive
ram (item 39) fully extended, the counterweight
piston drive pin (item 10) can be reached. With
drive ram fully retracted, the drive ram drive pin
(item 40) can be reached.
2 BLADE DISASSEMBLY:
Always wear cut protective gloves when han-
dling blades.
2.1 Remove two (2) hex lock nuts (item 42) and two
(2) socket head cap screws (item 38).
2.1.1 Push drive ram (item 39) into housing if
more space is required for blade removal.
2.2 END CUTTING BLADE:
2.3 Lower blade (item 56 or 64) away from blade
support (item 55 or 63) until crimp in end of
blade slides out of slot in blade support.
2.4 END GUIDED BLADE:
2.5 Lower blade (item 58) away from blade support
(item 57) and rotate blade until slot in blade
drops out of tabs on blade support end guides.
3 BLADE ASSEMBLY:
3.1 END CUTTING BLADE:
3.1.1 Slide blade (item 56 or 64) onto blade sup-
port (item 55 or 63) until crimp in end of
blade is touching end of support.
