operation and
maintenance instructions
Models EBS--1
page 8 of 12
JARVIS
6205012:.
®
PRODUCTS CORPORATION
33 ANDERSON ROAD, MIDDLETOWN, CONNECTICUT 06457--4926
UNITED STATES OF AMERICA E--MAIL.
TEL. 860--347--7271 FAX. 860--347--6978 WWW. j
arvisproducts.com
2.2 Depress the trigger to start the saw.
Always use two hands when starting the tool
and making the cut.
2.3 Guide the saw down through the brisket apply-
ing a steady, even pressure to both handles.
2.3.1 The blade end of the saw should be pointing
upwards during the first part of the cut.
2.3.2 As the brisket starts to open, rotate the saw
to a horizontal position to finish the cut.
2.4 Release the trigger to stop the saw.
Continue holding the tool with two hands un-
til the saw blade comes to a complete stop.
2.5 Remove the saw from the carcass.
2.6 Sanitize the saw blade.
MAINTENANCE INSTRUCTIONS
IMPORTANT:
ALWAYS DISCONNECT
THE
ELECTRIC POWER SUPPLY IN ACCORDANCE
WITH OSHA’S LOCKOUT/TAGOUT PROCE-
DURES (29CFR 1910.147) BEFORE INSTALLING
OR REMOVING A BLADE. ALWAYS DISCON-
NECT THE ELECTRIC POWER SUPPLY IN AC-
CORDANCE WITH OSHA’S LOCKOUT/TAGOUT
PROCEDURES (29CFR 1910.147) BEFORE PER-
FORMING ANY MAINTENANCE OR REPAIRS.
Refer to Figure A on page 4 for referenced items
1 PRIOR TO USE OR DAILY:
1.1 Make sure the control trigger is working correct-
ly.
Depress
the trigger and the tool should start.
Release
the trigger and the tool should stop.
If
the tool malfunctions, repair or remove it from
service immediately.
The electric power supply must be connected
to perform the above operation only.
Always use two hands when starting and
stopping the tool.
1.2 Apply
Jarvis
1315 White Grease
to grease fit-
ting (item 1). Apply grease to fitting by putting
a grease gun through the grease holes located on
the bottom cover (item 41).
Refer to Figure 2
.
Note: Correct application of grease into grease fitting
(item 1) depends on location of blade drive piston (item
9). If blade drive piston is fully extended, apply grease
to hole number 1. If blade drive piston is fully retracted,
apply grease to hole number 2.
1.3 Check all electrical plugs and cords (over their
entire lengths) for cuts and abrasions. Replace
if necessary.
2 MONTHLY:
2.1 Apply
Jarvis
1315 White Grease
to grease fit-
ting (item 40). Apply grease to fitting by putting
a grease gun through the grease holes located on
the bottom cover (item 41).
Refer to Figure 2
.
Note: Correct application of grease onto grease fitting
(item 40) depends on location of blade drive piston (item
9). If blade drive piston is fully extended, apply grease
to hole number 3. If blade drive piston is fully retracted,
apply grease to slot number 4.
Figure 2
Grease Holes
No. 1
No. 2
No. 3
No. 4
2.2 Inspect for wear on blade side guides (item 10).
Adjust for wear by removing outer set screws
(item 5). Turn inner set screws (item 5) to adjust
guide. Replace and tighten outer set screws to
secure adjustment. Replace side guides if neces-
sary.
3 BLADE REMOVAL:
3.1 Remove hex head screws (item 6).
3.2 Remove blade (item 8, 80 or 81) from blade
drive piston (item 9).
3.3 Slide blade (item 8, 80 or 81) through saw blade
guard (item 7) and blade top guide (item 11).
4 BLADE INSTALLATION:
4.1 Reverse steps and procedures outlined in section
3.
