Jandy WaterColors LED, Installation Manual

Page: 12 / 20

Page 12
Figure 6. Removing the Jandy WaterColors Light Assembly for Light Engine Replacement
1
POOL WALL
Power
Cord
Niche
POOL LIGHT
ASSEMBLY
PILOT SCREW
Push up on
bottom of
light assembly
2
Power
Cord
Niche
SPA LIGHT
ASSEMBLY
Bonding
cable
Unscrew pilot screw
and pull top of light
assembly away from
pool wall
Bonding
cable
7. Plug in the quick disconnect wire (white for the 7. Plug in the quick disconnect wire (white for the
12V and red for the 120V) onto the terminal 12V and red for the 120V) onto the terminal
(AC1) of the light engine.
(AC1) of the light engine.
8. Plug in the quick disconnect wire (black for the 8. Plug in the quick disconnect wire (black for the
12V and blue for the 120V) onto terminal (AC2) 12V and blue for the 120V) onto terminal (AC2)
of the light engine.
of the light engine.
b. Large Light Engine (PCB) Replacement (120V b. Large Light Engine (PCB) Replacement (120V
and 12V) and 12V)
1. Remove three (3) nuts and washers. 1. Remove three (3) nuts and washers.
2. Unplug the quick disconnect terminals from the 2. Unplug the quick disconnect terminals from the
PCB. PCB.
3. Remove the light engine from the light fixture. 3. Remove the light engine from the light fixture.
4. Place new light engine into the fixture with the 4. Place new light engine into the fixture with the
orientation shown in Figure 8. orientation shown in Figure 8.
5 Secure the new light engine (PCB) with two (2) 5 Secure the new light engine (PCB) with two (2)
nylon washers and two (2) nuts. Torque to nylon washers and two (2) nuts. Torque to
12 in-lbs.
12 in-lbs.
6. Plug in the white quick disconnect wire onto the 6. Plug in the white quick disconnect wire onto the
terminal (J2) of the light engine. terminal (J2) of the light engine.
7. Plug in black quick disconnect wire onto terminal 7. Plug in black quick disconnect wire onto terminal
(J6) of the light engine for the 12V models; (J6) of the light engine for the 12V models;
or terminal (J3) of the light engine for 120V
or terminal (J3) of the light engine for 120V
models.
models.
8a. For 12V models, place a nylon washer on the 8a. For 12V models, place a nylon washer on the
stud and place the green ground wire terminal on stud and place the green ground wire terminal on
the nylon washer and secure both with the nut.
the nylon washer and secure both with the nut.
Torque to 12 in-lbs.
Torque to 12 in-lbs.
8b. For 120V models, place the green ground wire 8b. For 120V models, place the green ground wire
on the stud and secure with the nut. Torque to 12 on the stud and secure with the nut. Torque to 12
in-lbs.
in-lbs.
6. Reassemble the fi xture.
a. If not already done, remove the gasket from the a. If not already done, remove the gasket from the
glass lens and install a new gasket, P/N R0451101 glass lens and install a new gasket, P/N R0451101
for the large light and R0400501 for the small
for the large light and R0400501 for the small
light, on the lens. On the small light, remove the
light, on the lens. On the small light, remove the
diverger from the lens.
diverger from the lens.
NOTE A new lens gasket must be used each time the
light is reassembled.