background image

STEP 3
Inspect your light housing for signs of wear

Inspect  the  rubber  grommet  where  the  power  cord  enters  the  light  for  excessive 

deterioration.  Inspect  the  light  housing,  the  tensioning  clamp,  and  face  ring  for 

warping, dents and excessive rust. Do not install PureWhite into a light housing that 

appears to be worn out from prolonged exposure to pool water or mishandling.

STEP 7
Submerge assembled light into the water

Once the screws or clamp are tight, submerge the assembled light housing in the water 

and  visually  check  that  air  bubbles  are  not  escaping  from  the  gasket  area.  Should 

bubbles appear, immediately remove the light housing from the water and reset the 

gasket and lens. 
Once you are satisfied that there are no air leaks, complete the installation by wrapping 

the  cord  around  the  light  housing  and  re-attaching  the  light  housing  to  the  niche 

assembly.

STEP 8
Check for air bubbles when light is turned ON

Reconnect  power  to  the  pool  or  spa  light  by  resetting  the  circuit  breaker  to  the 

“ON”position. Go back to the light location and check for 

air bubbles

 rising to the 

surface from the light housing for at least 

10 minutes

. It is important that the lamp is 

turned on during this time. 
If you do not see air bubbles rising to the surface at anytime during the 10-minute 

inspection process, the housing is holding its water tight seal and the installation is 

complete.  You  are  now  ready  to  enjoy  your  new  PureWhite  Replacement  LED 

In-Ground Pool or Spa lamp. 
If you do see air bubbles rising to the surface at anytime during the inspection process, 

immediately remove the PureWhite lamp from the housing, dry it completely and reset 

the  gasket  and  lens.  Make  sure  that  the  PureWhite  lamp  and  light  housing  are 

completely dry before reassembling. 

 

If the light housing continually leaks water after 2 or more attempts at installation, 

replacement of the light housing may be necessary. 
Please read the J&J Electronics “PureWhite Quick Start Guide” for further installation 

advice. 

Note on Figures 1-3:

 All figures are provided for illustration purposes only. Refer to the 

original pool or spa light manufacturer’s installation manual for further reference.

STEP 4
Dry the light housing and lens

Make sure the inside of the light housing and glass lens are completely dry by wiping 

them down with a clean rag.

STEP 6
Reassemble the light housing

Proceed by cleaning any gasket residue from the light housing body. A clean surface 

is necessary for the new gasket to seat properly and prevent leakage. Install the new 

gasket onto the glass lens.

LPL-P2-WHT-12-S, LPL-P2-WHT-120-S, LPL-P2-WHT-12-SQ-S and

LPL-P2-WHT-120-SQ-S, LPL-M1-WHT-12, LPL-M1-WHT-120 

PureWhite Replacement LED In-Ground Pool and Spa Lamps
Use  the  pool’s  or  spa’s  current  light  switch  to  turn  “ON”  and  “OFF”  your  new 

PureWhite lamp.

Failure to install a new lens gasket could result in water leakage which can permanently 

damage the PureWhite lamp and cause serious injury or death due to electrical shock.
The product warranty is voided if the proper gasket is not installed.  See the “Gasket 

compatibility” section at the beginning this manual for details. 
Set the lens and faceplate in the light housing and re-assemble according to the light 

housing manufacturer’s specification. Tighten the screws or clamp slightly, allowing 

the gasket to seal evenly.

STEP 5
Install PureWhite lamp

Remove the old lamp and discard. Carefully screw the PureWhite lamp into the socket.

WARNING!  Always  use  a  new  lens  gasket  whenever 
reassembling your light housing.

Operation

Rev. 012114-SM1

J&J ELECTRONICS, INC 1-YEAR LIMITED WARRANTY

(For LPL-P2-WHT-12-S, LPL-P2-WHT-120-S, LPL-P2-WHT-12-SQ-S, LPL-P2-WHT-120-SQ-S, LPL-M1-WHT-12, LPL-M1-WHT-120)

J&J Electronics, Inc. (“J&J”) warrants the above-referenced model numbers of PureWhite LED In-ground Pool  and Spa Lamp (the “Product”) to be free from defects in material and 

workmanship, under normal use, conditions and service, for a period of one (1) year from the original date of purchase, subject to the terms specified herein. If during the warranty 

period, the Product fails to operate due to a defect in material or workmanship, J&J will, at its option, repair or replace the Product at no charge. 

TERMS AND CONDITIONS

This warranty is available to the original purchaser of the product(s) only. This warranty applies only when products are properly installed in an in-ground pool; any other use voids the warranty. Products 

must be used in lighting equipment designed and approved for the application and in environmental conditions within the normal specified operating range. This warranty does not apply to any 

abnormal use of product(s), use in violation of any applicable standard, code or instructions for use in installations including those contained in the latest National Electrical Code (NEC), the Standards 

for Safety of Underwriters Laboratory, Inc. (UL), Standards for the American National Standards Institute (ANSI). This warranty will not apply in the event of conditions demonstrating abnormal use or 

stress, freezing, operating when not fully submerged, under/over voltage/current conditions, excessive switching cycles or operating hours or outside the recommended operating conditions. This 

warranty does not apply to color shifts or dimming caused by emissions and/or LED color shifts and dimming that naturally occurs over time. 

Warranty conditions: If the product operates for 15 or 

more hours per day or continuously for 24 hours per day, the product warranty period stated shall be reduced to half the stated period. 

This warranty does not cover damage occurring during 

shipment, damage or failure resulting from alteration, accident, acts of God, theft, abuse, negligent installation, improper service, unauthorized repairs, freezing or where adequate care has not been taken 

to prevent damage to the product(s). Tampering with any internal component of this product(s) will void the warranty. 

This warranty gives you specific rights. You may have other rights that vary according to the laws of your state.

LIMITATION OF LIABILITY

THE FOREGOING SHALL CONSTITUTE THE EXCLUSIVE REMEDY OF THE PURCHASER AND IS IN LIEU OF ALL OTHER WARRANTIES, WHETHER EXPRESS OR IMPLIED, INCLUDING ALL WARRANTIES OF 

MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, AND ALL WARRANTIES ARISING FROM COURSE OF DEALING OR USAGE OR TRADE. THE LIABILITY OF J&J UNDER THIS WARRANTY SHALL 

BE LIMITED TO THE REPLACEMENT, REPAIR OR PRO-RATED CREDIT OF THE PRODUCT AS STATED HEREIN. J&J IS NOT RESPONSIBLE FOR SHIPPING OR TRANSPORTATION COSTS RELATED TO 

OBTAINING WARRANTY SERVICE. IN NO EVENT SHALL J&J BE LIABLE FOR ANY OTHER COSTS OR DAMAGES, INCLUDING LOST PROFITS OR REVENUES, LABOR CHARGES OR FOR ANY INCIDENTAL, 

SPECIAL OR CONSEQUENTIAL DAMAGES.

J&J reserves the right to change the warranty, warranty period without prior notice and without incurring obligation.

To  obtain  warranty  service,  retain  the  failed  Product,  retain  the  installation  invoice  showing  product  purchase  price  and  contact  J&J  Electronics,  Inc.  at  800.735.4553  ext.  242  or 

[email protected].  As of 1/21/14

For more information about this or other J&J Electronics lighting products, please visit www.purewhitepoollight.com.

©2014 J&J Electronics, Inc. All rights reserved. PureWhite is a trademark of J&J Electronics, Inc. All registered and trademarked brands and names are the property of their respective companies.

PAGE 2

J&J Electronics   

•  

 

6 Bendix, Irvine, CA 92618 USA   

•   

800.735.4553

   

•   

949.455.4460

   •   

www.jandjpoolspa.com

 

Reviews: