For LPL-P1-WHT-12 and LPL-P1-WHT-120
3-YEAR LIMITED WARRANTY
Product warranty
J&J Electronics, Inc. warrants the PureWhite Replacement LED
In-Ground Pool lamp (the Product) to be free from defects in material
and/or workmanship, under normal use, conditions and service, for
a period of three (3) years from the original date of purchase. If during
the warranty period, there is a defect in material or workmanship,
J&J Electronics, Inc. will repair or replace (at its discretion) the Product
under the conditions of the warranty. The warranty covers normal
consumer use of the Product. To obtain warranty service, contact
the establishment from which the Product was purchased.
Exclusions from warranty
The PureWhite Replacement LED In-Ground Pool lamp is designed
for use in In-Ground swimming pools only. If installed for use in any
other application, the warranty is void thereby releasing J&J
Electronics, Inc. from any and all claims related to its misuse. The
warranty does not cover and J&J Electronics, Inc. shall be held
harmless against any damage occurring during shipment, damage
or failure resulting from alteration, accident, theft, abuse, negligent
installation, improper service, unauthorized repairs or where adequate
care has not been taken to prevent damage to the Product. Tampering
with any internal component of this Product will void the warranty.
This warranty does not cover failure due to the presence of water
inside the niche fixture. This warranty excludes all incidental or
consequential damages except as required by state law. This warranty
gives you specific rights. You may have other rights that vary
according to the laws of your state.
STEP 2
Remove old lamp
Access the old lamp according to the original manufacturer’s pool light
installation manual. Remove the screws and/or loosen the clamp that holds
the face plate and lens in place. Carefully remove the lens from the pool
light housing. Take care not to damage the surface of the light housing
body that makes contact with the rubber gasket.
STEP 3
Inspect your light housing for signs of wear
Inspect the rubber grommet where the power cord enters the light for
excessive deterioration. Inspect the light housing, the tensioning clamp,
and face ring for warping, dents and excessive rust. Do not install
PureWhite into a pool light housing that appears to be worn out from
prolonged exposure to pool water or mishandling.
STEP 4
Dry the light housing and lens
Make sure the inside of the light housing and glass lens are completely
dry by wiping them down with a clean rag.
STEP 5
Install PureWhite lamp
Remove the old lamp and discard. Carefully screw the PureWhite lamp
into the socket.
STEP 6
Reassemble the light housing
Proceed by cleaning any gasket residue from the light housing body. A
clean surface is necessary for the new gasket to seat properly and prevent
leakage. Install the new gasket onto the glass lens.
WARNING! Always use a new lens gasket
whenever reassembling your pool light housing.
Failure to install a new lens gasket could result in water leakage
which can permanently damage the PureWhite lamp and cause serious
injury or death due to electrical shock.
Set the lens and faceplate in the light housing and re-assemble according
to the light housing manufacturer’s specification. Tighten the screws or
clamp slightly, allowing the gasket to seal evenly.
STEP 7
Submerge assembled light into the water
Once the screws or clamp are tight, submerge the assembled light housing
in the water and visually check that air bubbles are not escaping from the
gasket area. Should bubbles appear, immediately remove the light housing
from the water and reset the gasket and lens.
Once you are satisfied that there are no air leaks, complete the installation
by wrapping the cord around the light housing and re-attaching the light
housing to the niche assembly.
STEP 8
Check for air bubbles when light is turned ON
Reconnect power to the pool light by resetting the circuit breaker to the
“ON” position. Go back to the light location and check for
air bubbles
rising to the surface from the pool light housing for at least
10 minutes.
It is important that the lamp is turned on during this time.
If you do not see air bubbles rising to the surface at anytime during the
10-minute inspection process, the housing is holding its water tight seal
and the installation is complete. You are now ready to enjoy your new
PureWhite Replacement LED In-Ground Pool lamp.
If you do see air bubbles rising to the surface at anytime during the
inspection process, immediately remove the PureWhite lamp from the
housing, dry it completely and reset the gasket and lens. Make sure that the
PureWhite lamp and light housing are completely dry before reassembling.
If the pool light housing continually leaks water after 2 or more attempts
at installation, replacement of the pool light housing may be necessary.
Please read the J&J Electronics”PureWhite Quick Start Guide” for further
installation advice.
Note on Figures 1-3:
All figures are provided for illustration purposes only.
Refer to the original pool light manufacturer’s installation manual for
further reference.
Operation
For LPL-P1-WHT-12, LPL-P1-WHT-120 PureWhite Replacement LED
In-Ground Pool Lamps
Use the pool’s current light switch to turn “ON” and “OFF” your new
PureWhite lamp.
For more information about this or other J&J Electronics lighting products, please visit www.purewhitepoollight.com.
Rev. 012910
©2010 J&J Electronics, Inc. All rights reserved. PureWhite is a trademark of J&J Electronics, Inc. All registered and trademarked brands and names are the property of their respective companies.
J&J Electronics
•
35 Hammond, Irvine, CA 92618 USA
•
800.735.4553
•
949.455.4460
•
www.jandjpoolspa.com
PAGE 2
