AIR & WATER HOSE REEL
PRO SERIES EXTREME - RETRACTABLE
Extreme Ultraflex Reinforced Hose is a special blend of hose that has been
developed for today’s demanding conditions, it stay flexible in the cold and doesn’t
kink in the heat, allowing full flow in all-weather conditions. It’s a tough hose for
tough conditions
FEATURES
Hose layering system
Auto lock / rewind
No tools required adjustable hose stop
Wall mount with 180° pivot
Weather resistant UV stabilised polypropylene case
Leader hose 1 m with brass fittings (AIR ONLY)
Leader hose 1 m with 12 mm brass tap fittings (WATER ONLY)
Includes Jamec Pem Extreme Ultraflex Hose
Bench top / short reach applications
SPECIFICATIONS
Part No.
58.3067
58.4023
Hose length
8 m
8 m
Hose I.D
9.2 mm (3/8")
10.5 mm (1/2")
Hose O.D
15.2 mm (5/8")
16.5 mm (5/8")
Leader hose length
1 m with 1/4" BSP Male fitting
1 m with brass tap fittings
Hose material
Extreme Ultraflex Reinforced Hose
Extreme Ultraflex Reinforced Hose
Reel / case type
Retractable / polypropylene
Retractable / polypropylene
Auto lock / rewind
Yes
Yes
Max. working pressure
300 psi
150 psi
Fitting size
1/4" BSP Male
12 mm Tap fittings
Bracket
180° Pivoting
180° Pivoting
Weight - kg
4.1
4.5
Product dimensions
451.9 L x 206 W x 314 D mm
451.9 L x 206 W x 314 D mm
Advised application
Air
Water
MAINTENANCE
Always keep the hose clean.
If the hose becomes dirty, clean it with a damp cloth while retracting.
DO NOT twist the hose while in use.
Mount the hose reel in a sheltered area to assist and protect the performance of
the hose and hose reel.
DO NOT allow the hose to contact any corrosive chemicals or fluids.#Always
retract the hose when not in use.
The Jamec Pem Hose Reel contains
a pre-tensioned spring inside
the inner drum assembly.
PRODUCT IDENTIFICATION
1.
Mounting bracket
2.
Pivot pin
3.
Fully enclosed case
4.
Carry handle
5.
1 m Leader hose with
1/4" BSP Male fitting
6.
Hose with adjustable stopper
7.
1 m Leader hose with
brass tap fittings
8.
12 mm Tap fittings
1
3
5
7
8
6
2
4
0.8 metre min.
INSTALLATION
The Jamec Pem Hose Reel can
be mounted in a horizontal or
vertical position.
1.
Choose a location that is
near to the compressed air
source.
2.
For large areas, place the
hose reel at the centre of
the work area.
3.
When mounting the hose
reel vertically, ensure there
is adequate clearance under the reel to prevent injury or
damage
4.
Mounting bracket must be installed on a flat surface.
Note: It is recommended to install the mounting bracket 0.8
metre (minimum) above the floor level
5. Drill 4 holes to match the holes located in the Mounting
Bracket. (Fig. 1)
6. Connect the hose reel to the Mounting Bracket with the
Pivot Pin. (Fig. 2)
Note: For fixed in-line position, fit the locking plate onto the
Mounting Bracket prior to inserting the pivot pin. (Fig. 3)
7.
Connect the inlet leader hose to the compressed air
source.
Note: Apply thread sealing tape to all air line and air hose
fittings.
OPERATION
1.
Slowly pull out the hose to the required length. A ‘clicking’
noise will be heard every revolution of the inner drum. To
lock the reel, allow the hose to retract slowly after hearing
the second or third ‘click’.
2.
To release the hose, pull it out until the ‘clicking’ noise
stops, and then allow the hose to slowly retract while
guiding it back into the hose reel. The self layering
mechanism will coil the hose back onto the inner drum.
3.
To avoid injury and damage, always hold the hose while it
is retracting.
Fig. 1 Mounting Bracket
Fig. 2 Pivot Pin
Fig. 3 Locking Plate
IMPORTANT
:
If the hose becomes tangled and will not retract - slowly pull out the hose past the
tangled section and then allow the hose to slowly retract while guiding it back
into the hose reel.
Always ensure the hose is clean and not twisted.
• Do not attempt to open the inner drum assembly.
WARRANTY EXCLUSIONS
The hose, rubber o-rings and hose stopper are deemed normal wear items and are
not covered under warranty.
The warranty does not extend to parts or components affected or damaged by
accident, normal wear, misuse, neglect or faulty installation.
To register a warranty claim visit: jamecpem.com
Distributed by
TRADEPEM INDUSTRIAL PTY LTD.
