JALpower JP5535 User Manual Download Page 29

Page: 29 / 31

Rated Parameters Setting

JP5535 True Online 1-3K UPS User Manual

Annex C. Rated Parameters Setting

Rated parameters of JP5535 1-3K UPS can be set from panel. Please set rated parameters in

according to the following procedures:

1) Start UPS power supply and ensure that rectifier, inverter, bypass and discharge are not

working.

2) Press ON/OFF and FUNC together for 2.5 seconds to enter in setting mode, all LEDs flicker.

3) Voltage setting: press FUNC to change rated voltage. Shown as following:

VAC

INPUT

VAC

OUTPUT

CONVERTER

BYPASS

LOAD

Current Rated

Voltage

4) Frequency setting: Press ON/OFF to choose voltage and enter in frequency setting. Press

FUNC to change rated frequency. Shown as following:

5) Mode setting: press ON/OFF to choose frequency and enter in mode setting, press FUNC

to change mode. First code: n-normal mode, E-ECO mode. Second code indicated current

voltage/frequency are listed in description of main menu in section 6.

Summary of Contents for JP5535
































Search results

Summary of Contents for JP5535

Reviews:

Related manuals for JP5535

Brands by name

Popular brands

JALpower JP5535, User Manual

Search results

Summary of Contents for JP5535

Reviews:

Related manuals for JP5535

Brands by name

Popular brands