background image

Service and repairs

Item no. 10404131, Revision 10

33 ( 36 )

HF spindle becomes loud

Cause

Troubleshooting

Tool unsuitable

q

Only use balanced tools.

(Also see the "Tools for high speed cutting

 [

}

 28]

" section.)

q

Check the tool for damage.

q

Replace damaged tool.

HF spindle is not
clamped truly or is dis-
torted

q

Only use spindle holders from the original accessories or
holders produced according to the tolerances specified by

Nakanishi Jaeger GmbH

.

HF spindle clamped
too tightly

q

Only tighten the clamping screws of the spindle holder
manually.

q

Do not use technical aids to clamp the HF spindle.

Bearings damaged

q

Contact 

Nakanishi Jaeger GmbH

 service.

No automatic tool change

Cause

Troubleshooting

Contamination

q

Remove all contamination between the tool taper and
shaft of the HF spindle.

(Observe all points in the “Tool change

 [

}

 25]

” and “Mainte-

nance

 [

}

 29]

” sections.)

Lack of pressure

q

Check the connections for compressed air.

q

Check the hoses for compressed air.

q

Check the pneumatic circuit.

q

Check the setting of the compressed air for the tool
change.

(Also see the "Setting values

 [

}

 23]

" section.)

Sensor does not send any

signals

Cause

Troubleshooting

No connection to sen-
sor

q

Check the lines and connections.

Summary of Contents for Z80-K450.21 S5





































Reviews: