1
SPOUT ASSEMBLY
2
TEE AND HOSE ASSEMBLY
Insert RUBBER WASHER (2) into groove
in SPOUT ESCUTCHEON BASE (3). Insert
SPOUT SHANK (1) through center hole of
sink or mounting surface.
Assemble RUBBER WASHER (4),
FIBER WASHER (5) and LOCKNUT (6)
onto threads of SPOUT SHANK (1)
from underside of lavatory or mounting
surface.
Push one RING WASHER (1) and one of the 0-RING (2) onto end of
SPOUT SHANK (3).
Slide the TEE (4) onto SPOUT SHANK (3) until it makes contact
with the 0-RING (2). Push the other 0-RING (2) and RING WASHER (1)
onto the SPOUT SHANK (3). Make sure both 0-RINGS (2) are seated
into grooves of TEE (4).
Thread LOCK NUT (5) onto SHANK (3). Rotate TEE (4) about
10 degrees from center and tighten securely.
Insert FIBER WASHERS (6) into COUPLING NUTS (7) of
SUPPLY HOSES (8) and tighten.
Align SPOUT (7) and tighten
LOCKNUT (6). Insert LIFT ROD (9)
through SPOUT (7).
1
2
4
5
6
3
Turn off hot and cold water
supplies before beginning.
CAUTION
7
2
2
1
5
6
6
1
3
4
GROOVE IN TEE
GROOVE IN TEE
10˚
7
7
8
8
5
3
WATER SUPPLY CONNECTIONS
Connect water supply to VALVE BODIES (1) with 1/2" IPS
FLEXIBLE SUPPLIES (3) or 3/8" O.D. BULL-NOSE RISERS (4).
Use wrench to tighten connections.
Do not over tighten. Be careful not to kink copper supply when
bending. Use tubing cutter to cut to proper length.
1
4
FERRULE
NOTE: FLEXIBLE SUPPLIES OR BULL-NOSE RISERS MUST BE
PURCHASED SEPARATELY.
COUPLING
NUT
1 0 9 4 5 1
1 0 9 4 5 1
Widespread Lavatory Faucets
Plumbers' Putty or Caulking
Adjustable Wrench
Phillips Screwdriver
Channel Locks
TOOLS REQUIRED
Tubing Cutter
Regular Screwdriver
Basin Wrench
GROOVE
APPLY SEALANT
OR TEFLON TAPE
4
A FOAM SEAL (1) is installed on underside of FLANGE (2). (Plumbers
Putty may be used in place of FOAM SEAL (1) if desired.)
Apply sealant or Teflon tape to threads of TAILPIECE (10) and
thread into DRAIN BODY (7) making a water tight seal.
Drop FLANGE (2) into LAVATORY DRAIN (3). From below assemble
RUBBER GASKET (4), PLASTIC WASHER (5) and LOCK NUT (6) onto
DRAIN FLANGE (2). Do not tighten fully.
INSTALL POP-UP DRAIN
FIG. 4a
FIG. 4b
FIG. 4c
FIG. 4c
FIG. 4a
FIG. 4b
1
4
3
2
5
6
7
8
6
9
2
Adjust STOPPER (13) height by repositioning POP-UP ROD (16) in SWIVEL (15)
and tightening SET SCREW (18).
Assemble POP-UP SWIVEL (15) to PIVOT ROD (11) but do not tighten.
Drop POP-UP ROD (16) through other hole in POP-UP SWIVEL (15) and
tighten SET SCREW (17)
Assemble PIVOT ROD (11), and PIVOT NUT (12) as shown. Install CONCAVE
WASHER (19) into PIVOT ROD OPENING (9) if not preinstalled. Hand tighten
PIVOT NUT (12). Drop STOPPER (13) into drain.
(
To vandal proof drain rotate STOPPER (13) so PIVOT ROD (11) goes
through EYE (14) of STOPPER (13)
. Make connection to "P" TRAP.
Inspect inside DRAIN BODY (7) that SEAL (8) is installed. Thread
DRAIN BODY (7) tight against FLANGE (2) to make a water tight seal.
10
9
7
6
12
19
16
15
17
18
2
10
14
13
11
The PIVOT ROD OPENING (9) in DRAIN BODY (7) should face the rear
of the lavatory. Tighten LOCK NUT (6) on FLANGE (2) to make a water
tight connection with channel locks. Do not over tighten.
3
INSTALL VALVE BODIES AND HANDLES
1-1/4'' MAX.
Thread LOCKNUT (1) to bottom of VALVE BODY (2). Make sure
FIBER WASHER (3) and RUBBER WASHER (4) are installed.
Insert VALVE BODY (2) through mounting hole from underside
of lavatory or mounting surface.
Note: VALVE BODY marked Hot is installed in the left mtg. hole,
VALVE BODY marked Cold in the right when facing front of fitting.
Maximum mounting surface thickness is 1-1/4".
From top install RUBBER WASHER (5) onto VALVE BODY (2). Thread
MOUNTING RING (6) on VALVE BODY (2). Thread HANDLE BASE (11)
onto VALVE BODY (2) until tIght against it's internal stop. Thread
MOUNTING RING (6) counter-clockwise until tight against HANDLE
BASE (11). Set VALVE BODIES (2) so that their outlets are facing
toward SPOUT TEE (7). Tighten LOCKNUT (1) using 35mm
or adjustable wrench.
Insert FIBER WASHERS (8) into COUPLING NUTS (9) of SUPPLY
HOSES (10) and tighten making water tight connection.
Important: Loop SUPPLY HOSES (10) as illustrated so they do not kink.
6
1
8
HOT
9
10
3
7
4
5
2
12
JADO
MOUNTING SURFACE
11
14
15
13
HOT
COLD
INSTALL HANDLES
Install HANDLE (13) onto VALVE STEM (12). Install HANDLE SCREW (14)
and tighten to secure HANDLE (13). Thread INDEX CAP (15) into HANDLE (13).
ROUGHING-IN
DIMENSIONS
30º
1-1/4" MAX.
1-1/8" D.
2-1/8" D.
6" TO 12" MAX.
2" MAX.
6-1/8"
5-1/8"
2-1/8" D.
2" MAX.
7" MAX.
MOUNTING
SURFACE
1-1/4" O.D.
NOTE: MOUNTING HOLES
ARE 1-1/8" D.
2-3/4" D.
Remove INDEX CAP (15), HANDLE SCREW (14), KNOB (13),
HANDLE BASE (11), MOUNTING RING (6) and RUBBER
WASHER (5) from VALVE BODIES (2).