Installation Instructions
To ensure that your installation proceeds smoothly--please
read these instructions carefully before you begin.
© J A D O U S A 2 0 0 5
P r o d u c t s
L u x u r y F a u c e t s a n d A c c e s s o r i e s
Product Numbers
Determine where the finished wall location will be.
This measurement
is very important!
Note: The rough-in measurement from the finished
wall is; 2" minimum and 2-3/4" maximum. This is a 3/4"
tolerance. See rough-in illustration above.
Plumbers' Putty or Caulking
Teflon Sealing Tape
3/8" hex wrench
Adjustable Wrench
Phillips Screwdriver
TOOLS REQUIRED
Regular Screwdriver
3
INSTALL WALL SPOUT and HANDLE SUPPORTS
5
11
4
4
9
10
12
1
2
3
8
7
13
6
Remove PLASTER GUARDS and unthread ROUGH-IN NIPPLE (7).
Remove SET SCREW (1) from SPOUT (2) with 2.5mm HEX WRENCH (10) supplied.
Pull SPOUT ADAPTER (3) from SPOUT (2). Uthread SPOUT NIPPLE (4) from
SPOUT ADAPTER (3).
Inspect that SPOUT NIPPLE O-RINGS (5 & 6) are seated in the grooves of SPOUT
NIPPLE (4).
See View A.
Thread SPOUT NIPPLE (4) into VALVE BODY (11) and tighten using a 3/8" hex wrench.
Thread SPOUT ADAPTER (3) onto SPOUT NIPPLE (4) so that the face extends
1" beyond finished wall.
See Figure "2"
.
Install ESCUTCHEON O-RING (8) in back of SPOUT ESCUTCHEON (9). Install the
SPOUT ESCUTCHEON (9) onto SPOUT (2).
Push SPOUT (2) onto SPOUT ADAPTER (3) and press tight against
finished wall. Align SPOUT (2) and tighten SPOUT SET
SCREW (1) with 2.5mm HEX WRENCH (10).
View A
View A
5
TEST INSTALLED FAUCET
Unthread SPOUT END and remove AERATOR.
Thread HANDLE SUPPORTS (12) onto
CARTRIDGE (13) and tighten with
adjustable wrench.
With HANDLES in OFF position, turn on
WATER SUPPLIES and check for leaks.
Operate both HANDLES to flush water
lines thoroughly.
Turn HANDLES off and replace AERATOR.
6
HELPFUL HINTS FOR CLEANING AND MAINTENANCE
The solid brass product you have just purchased has been designed to give you years of beauty and service. It is
important to bring to your attention proper care and maintenance procedures, which will ensure its lasting beauty.
First and foremost, it is important (as it is with any fine piece of jewelry or furniture) that the product be wiped clean and
dry with a soft damp cloth after every use.
Second, under no circumstances should an abrasive cleaner or combination cleaner/polish be used on JADO products.
The abrasive nature of such products will eventually destroy the finish and void the warranty.
In the event of stubborn blemishes shown on the finish, we recommend use of Windex window cleaner with a soft cloth,
but we do not recommend it be used on an everyday basis.
ROUGHING-IN
DIMENSIONS
Channel Locks
Wall Mount Vessel Faucet
H 9 6 5 5 7 8
H 9 6 5 5 7 8
H 9 6 5 5 7 8
H 9 6 5 5 7 8
JADO USA
6615 West Boston
Chandler, AZ 85226
Phone:(8OO) 227-2734
Fax: (8OO) 552-JADO(5236)
www.jadousa.com
TO THE PURCHASER OF JADO BRASS PRODUCTS
Attention installer:
Please leave This Pamphlet for The Owner
POLISHED BRASS AND CUSTOM FINISH WARRANTY
: A 1 YEAR LIMITED FINISH WARRANTY from date of purchase is provided to the
first residential owner against defects in materials and workmanship. Due to the ever-changing finish of Patina products, the finish warranty
is excluded. Warranty shall not include problems related to the installation of the product.
MECHANICS
MECHANICAL WARRANTY:
A LIFETIME LIMITED WARRANTY is provided to the first residential owner on parts to be free from failure
related to defects in materials and workmanship but not installation.
CONDITIONS TO WARRANTIES
JADO Bathroom & Hardware Manufacturing Corp. places the following conditions on its finish and mechanical warranties to the first residential owner only.
JADO finish and mechanical warranties are limited to products correctly installed and used in a residential environment.
JADO warranties will not assume liability for damage due to abuse, mishandling, incorrect installation, improper maintenance, or deterioration
due to normal use.
JADO will not be liable for labor or other costs relating to the sale, installation, or replacement of their products.
In the event of a defect in any JADO product covered by this warranty, the product must be returned to the dealer where originally purchased
along with proof of purchase.
JADO's obligation under the warranty shall be limited to the repair or exchange of any product which has been determined by JADO to be
defective after appropriate examination.
The state of California has mandated under Proposition #65 that
manufactures of products, including faucets which come into
contact with potable water, must warn the consumer if the product
contains materials listed by the state as a carcinogen or
reproductive toxin. Lead, which is contained in all brass faucets in
limited amounts appears on the State's list.
Preliminary industry tests have indicated that users of faucets
made from brass face no significant danger, however,
California Proposition #65 requires that we provide you with the
following notice:
NOTICE: JADO products conform to industry
requirements of water conservation under the
ASTM / ANSI A112.18.1M-1994 plumbing code.
Lavatory, bidet, wet bar and kitchen faucet sets
have a maximum flow rate of 2.2GPM. Shower
heads, hand showers and body sprays have a
maximum flow rate of 2.5GPM.
Warning: This product contains an element
known to the State of California to cause cancer
of reproductive harm.
JADO BATHROOM AND HARDWARE MFG. CORP.
6615 West Boston
Chandler, AZ 85226
JADO warrants this product to be free from defects in materials or workmanship for as long as the original consumer purchaser
owns their home.
JADO will provide, free of charge, at it’s sole option, replacement part(s) or product (or if no longer available, a comparable
product) to replace those which have proven defective in materials or workmanship.
Proof of purchase (original sales receipt) from the original consumer purchaser must be made available to JADO for all limited
warranty claims. This limited warranty is non transferable. It does not apply in the event of product damage due to the use of other than
genuine JADO replacement parts, installation error, abuse, misuse, or improper care and maintenance (whether performed by
a plumber, contractor, service provider or member of the purchaser’s household). The limited warranty excludes damage due to aggressive
air or water conditions, or harsh or abrasive cleaners and/or materials. This limited warranty excludes all industrial, commercial and business
usage, whose purchasers are hereby extended a two year limited warranty (with the exception of solenoid valves and other electronic
components which carry a one year limited warranty) applying to all other terms of this limited warranty except duration. This limited warranty
does not cover labor charges incurred and/or damages sustained in installation, repair or replacement, nor incidental or consequential
damages, all of which are expressly disclaimed. This limited warranty is applicable only to JADO faucets manufactured after June 1, 1996
and installed in the United States and/or Canada.
This limited warranty gives the original consumer purchaser of an JADO faucet specific legal rights which may vary from state to
state or from province to province. This limited warranty does not cover any liability for consequential or incidental damages, all of which
are hereby expressly disclaimed, or the extension beyond the duration of this limited warranty of any implied limited warranties, including
those of merchantability or fitness for an intended purpose. In some states or provinces the exclusion or limitation of incidental or consequential
damages is not allowed, so those exclusions may not apply to you.
JADO Bathroom & Hardware Manufacturing Corp. provides the following warranties only to the first residential owner of our products.
FINISHES
JADO FAUCET LIFETIME FUNCTION AND FINISH LIMITED WARRANTY
2
1
4
3
5
6
ON
OFF
ON
OFF
AERATOR
SPOUT END
INSTALL CROSS HANDLES
Place ESCUTCHEON O-RING (1) in groove on back side of
ESCUTCHEON (2).
Install ESCUTCHEON (2) onto HANDLE ADAPTER (3).Thread
HANDLE ADAPTER (3) onto HANDLE SUPPORT (4) until tight
against finished wall.
Turn valves to off position. Align CROSS HANDLE (5)
as shown or as desired. Install CROSS HANDLE (5) onto
HANDLE ADAPTER (3). Thread HANDLE BASE (6) until
tight against ESCUTCHEON (2).
4
Wall Mount
Vessel Faucet
832/34O/...
Trim Only
832/375/...
1
INSTALL WALL BRACKET
Secure WALL BRACKET (1) to cross brace of wall structure
at required height using six wood screws.
NOTE TO INSTALLER:
IF REQUIRED A DEEP ROUGH KIT IS
AVAILABLE, PART NUMBER H960740.191.
WOOD SCREWS
CROSS BRACE
WALL STUDS
1
16"
2
INSTALL VALVE BODY
Mount VALVE BODY (1) to WALL BRACKET (2) as shown. Level and tighten
SET SCREWS (3) to secure VALVE BODY (1) to WALL BRACKET (2).
Connect HOT water supply to LEFT INLET UNION (4) and COLD water supply
to RIGHT INLET UNION (5). Pipe connections are 1/2" NPT. Use sealant or
Teflon tape on pipe connections.
Do not solder directly to valve body.
With valves closed open supply lines and check for leaks. Remove PLASTER
GUARDS (6) and open both valves and check for leaks.
HOT
COLD
Close both valves and turn off water supplies. Replace PLASTER GUARDS (6)
and finish wall construction.
6
6
5
4
2
1
3
-
Figure 2
1"
(25mm)
3/8"
HEX
GREASE O-RING
(SUPPLIED)
FINISHED
WALL
FACE
1-5/8" MIN.
(41mm)
1/2" NPT
UNION INLETS
8"
(203mm)
5-1/4"
(133mm)
1"
(25mm)
7/8" MAX.
(22mm)
2-1/2" MAX.
(63mm)
FINISHED
WALL
FINISHED
WALL
2-3/8" D.
(60mm)
7-1/4"
(184mm)
IQ
™
ON
OFF
OFF
