1
INSTALL FAUCET (LAVATORY AND BIDET)
Turn off hot and cold water
supplies before beginning.
CAUTION
ROUGHING-IN
DIMENSIONS
Feed FAUCET SUPPLY TUBES (3) and SHANK (4) through ESCUTCHEON (1) and mounting hole of lavatory, bidet
or mounting surface.
SINGLE HOLE MOUNTING
Inspect ESCUTCHEON (1) for O-RING (2) fitted into
O-ring groove
. Place ESCUTCHEON (1) with O-RING (2) over mounting hole.
FAUCET INSTALLATION WITH OPTIONAL DECK ESCUTCHEON (8).
Thread two (2) 2-1/4" long ESCUTCHEON STUDS (12) into base of DECK ESCUTCHEON (8).
Install the two (2) 0-RINGS (9) into the recesses under the DECK ESCUTCHEON (8). Place the DECK ESCUTCHEON (8)
onto the mounting surface. From below install two (2) FLAT BRASS WASHERS (10) onto the ESCUTCHEON STUDS (12)
and secure with WING NUTS (11) supplied with kit. Before final tightening, DECK ESCUTCHEON (8) should be centered
on mounting surface. Tighten WING NUTS (11).
With DECK ESCUTCHEON (8) installed, complete the installation following the instructions above
(SINGLE HOLE MOUNTING).
From below, Install RUBBER WASHER (5), RETAINING WASHER (6) and LOCKNUT (7) onto faucet SHANK (4).
Before final tightening, faucet should be seated flush on ESCUTCHEON (1). Adjust faucet so that it is centered and covers
mounting hole. Tighten LOCKNUT (7) using a 13mm or adjustable wrench. Do not over tighten. Install POP-UP ROD (13).
BIDET
MOUNTING
SURFACE
3
2
5
1
WATER SUPPLY CONNECTIONS
Supply connections are made after bidet has bee installed.
Important: Use only SUPPLY ADAPTERS (1) furnished with
lavatory or bidet faucet.
Assemble SUPPLY ADAPTERS (1)
(furnished) to FAUCET SUPPLY TUBES (2) as shown in
Figure 2a
. Push SUPPLY ADAPTER (1) onto SUPPLY TUBE (2)
and tighten SUPPLY NUT.
Connect water supplies to SUPPLY ADAPTERS (1)
with 1/2" IPS FLEXIBLE SUPPLIES (3) or 3/8" O.D.
BULL-NOSE RISERS (4). Connect HOT supply to
left side and Cold to right side.
Use adjustable wrench to tighten connections.
Do not over tighten. Be careful not to kink
copper supply when bending. Use tubing cutter
to cut to proper length.
3
4
FERRULE
COLD
HOT
BRASS SPLIT RING
BRASS FRICTION WASHER
RUBBER SEAL
NOTE: FLEXIBLE SUPPLIES OR BULL-NOSE RISERS MUST BE
PURCHASED SEPARATELY.
SUPPLY NUT
FAUCET SUPPLY TUBE
Lavatory
Figure 2a
13
13
LAVATORY
MOUNTING
SURFACE
11
5
10
1
4
3
2
9
12
9
8
12
6
7
6-1/2"
NOTE: MOUNTING HOLE
IS 1-3/8" D.
2-5/8" D.
2-5/8" D.
14-5/8"
MAX 1-5/8"
MAX 1-5/8"
4-7/8"
3-1/8"
28
2-1/8"
1-1/4" O.D.
1-1/4" O.D.
MAX 2"
7"
5-3/4"
4-7/8"
80
3-1/4"
14-5/8"
2-1/8"
MAX 2"
7"
GROOVE
Bidet
H
O
T
CO
O-RING GROOVE
H
O
T
CO
H
O
T
CO
H
O
T
CO
1 0 9 1 2 7
1 0 9 1 2 7
Plumbers' Putty or Caulking
Adjustable Wrench
Phillips Screwdriver
Channel Locks
TOOLS REQUIRED
Tubing Cutter
Regular Screwdriver
Basin Wrench
Lavatory
Bidet
APPLY SEALANT
OR TEFLON TAPE
2
A FOAM SEAL (1) is installed on underside of FLANGE (2). (Plumbers
Putty may be used in place of FOAM SEAL (1) if desired.)
Apply sealant or Teflon tape to threads of TAILPIECE (10) and
thread into DRAIN BODY (7) making a water tight seal.
Drop FLANGE (2) into LAVATORY DRAIN (3). From below assemble
RUBBER GASKET (4), PLASTIC WASHER (5) and LOCK NUT (6) onto
DRAIN FLANGE (2). Do not tighten fully.
INSTALL POP-UP DRAIN
FIG. 2a
FIG. 2b
FIG. 2c
FIG. 2c
FIG. 2a
FIG. 2b
1
4
3
2
5
6
7
8
6
9
2
Adjust STOPPER (13) height by repositioning POP-UP ROD (16) in SWIVEL (15)
and tightening SET SCREW (18).
Assemble POP-UP SWIVEL (15) to PIVOT ROD (11) but do not tighten.
Drop POP-UP ROD (16) through other hole in POP-UP SWIVEL (15) and
tighten SET SCREW (17)
Assemble PIVOT ROD (11), and PIVOT NUT (12) as shown. Install CONCAVE
WASHER (19) into PIVOT ROD OPENING (9) if not preinstalled. Hand tighten
PIVOT NUT (12). Drop STOPPER (13) into drain.
(
To vandal proof drain rotate STOPPER (13) so PIVOT ROD (11) goes
through EYE (14) of STOPPER (13)
. Make connection to "P" TRAP.
Inspect inside DRAIN BODY (7) that SEAL (8) is installed. Thread
DRAIN BODY (7) tight against FLANGE (2) to make a water tight seal.
10
9
7
6
12
19
16
15
17
18
2
10
14
13
11
The PIVOT ROD OPENING (9) in DRAIN BODY (7) should face the rear
of the lavatory. Tighten LOCK NUT (6) on FLANGE (2) to make a water
tight connection with channel locks. Do not over tighten.
