42
Additional Care and Maintenance Instructions:
1.
Debris can accumulate on the spa cover. Removal of snow or
other debris will help to avoid breakage of the foam cores.
2.
Be sure to lock the cover straps to secure the cover from un-
wanted or accidental entry.
3.
Do not place heavy objects on the vinyl.
4.
Do not walk, sit or stand on the cover.
5.
Do not drag or use the flaps/skirt or the cover lock straps to
remove the cover.
6.
Use only recommended cover lift systems.
7.
Use only chemicals and cleaners recommended by Jacuzzi.
8.
Remember to keep spa covered when not in use. Maintaining
proper water levels assures efficient operation and efficient elec-
trical usage.
9.
Do not expose your spa to the sun for extended periods of
time as UV rays can damage the interior surface.
10.
Use caution when removing cover. Before removing cover,
assure all locks have been released to avoid lock breakage and or
cover strap damage.
Tool Free Access Door
The Tool Free Access door provides fast access to the equipment
bay and components without the need of tools. To remove the
door, follow the steps below.
Note:
To avoid any injuries, more than one individual must per-
form these steps.
1
2
3
1.
Locate the door’s retractable push button on the top of the
front panel (1).
2.
Press the retractable push button to release the panel door
from the spa frame (2).
3.
Slowly and gently tilt the panel forward to remove (3). This will
expose the equipment bay for easy access to the components.
Place the panel in a safe location to prevent from damaging it.
4.
To reinstall the panel just follow the steps above in reverse order.
Maintaining The Synthetic Cabinet
Your new spa’s synthetic cabinet requires little or no mainte-
nance of any kind. To clean, simply wipe cabinet with a clean
towel and mild soap solution.
ATTENTION: Never spray cabinet with a garden hose for any
reason since this action may induce an electrical short in the
spa’s electrical equipment.
Winterizing
Your Jacuzzi spa is designed to automatically protect itself
against freezing when operating properly.
During periods of severe freezing temperatures, you should
check periodically to be certain that the electrical supply to the
spa has not been interrupted.
In extreme bitter cold weather, less than 0°C (32°F), program
the primary filtration cycle to run for 24 hours to prevent
freezing
If you do not intend to use your spa, or if there is a prolonged
power outage during periods of severe freezing temperatures,
it is important that all water be removed from the spa and
equipment to protect against damage from freezing.
Expert winterization of your spa is highly recommended,
contact your authorized Jacuzzi dealer.
In emergency situa-
tions, damage can be minimized by taking the following steps:
1.
Turn off power to the spa.
2.
Follow the directions for draining the spa.
3.
Turn the massage/diverter selector(s) into the middle combo
position to allow the water in the plumbing lines to drain.
4.
Turn the waterfall valve(s) to the open position to allow the
water in the plumbing lines to drain.
5.
Open all the air controls and leave them open until you re-
sume use of the spa.
6.
As the water level drops below the seats, use whatever means
necessary to get the water out of the recessed seating areas and
into the footwell, such as a wet/dry vacuum.
7.
When the water level ceases to drop, use whatever means
available to remove any remaining water from the foot well, such
as a wet/dry vacuum.
8.
Remove the synthetic cabinet panel under the control panel
and locate the drain plugs on the front of the pump(s). Remove
plugs to allow water to drain out of pumps and heater.
Note:
Use a wet/dry vacuum or other means to keep this from
flooding the equipment compartment. Replace the drain plugs.
9.
Loosen the hose clamp on the circulation pump intake behind
the control box and pull the hose off (twist hose back and forth
while pulling outward). Tip hose down and allow to drain, then
reinstall hose and clamp.
10.
Loosen hose clamp at bottom of CLEAR
RAY®
system and
pull hose off of CLEAR
RAY®
fitting (twist the hose back and forth
while pulling downward). Tip hose down and allow to drain. Then
reinstall hose and clamp. Remove the cover of the CLEAR
RAY®
system to access the UV bulb and quartz tube. Remove and store
the UV bulb in a safe location. Remove and dry off the quartz
tube then reinstall it. Depending on the length of time, consider
replacing the UV bulb when you resume use of your hot tub.
11.
Reinstall synthetic cabinet side panel and cover spa so that
no casual moisture can enter into it.
Restarting Your Spa in Cold Weather
If you want to start up your spa after it has sat empty for a time
in freezing temperatures, be aware that the water remaining in
certain sections of the piping may still be frozen. This situation
will block water flow preventing the spa from operating properly
and possibly damaging the equipment.
Summary of Contents for J-300 Series
Page 2: ......
Page 3: ...Italiano Avvertenze 4 English Warnings 28 Fran ais Recommandations 51...
Page 79: ...79...
