OPERATION
Normal Operation
Whirlpool System:
You can enjoy the Aero Plus spa with or without activat-
ing the whirlpool. Either way, bathing in your spa can be
pleasurable, as well as therapeutic. After a busy,
stressful day, you can look forward to soaking in your
spa in still water with no turbulence—only the gentle
warmth of the soothing and relaxing water.
For an invigorating spa experience, you can take
advantage of the built-in whirlpool system. To do this,
push the SYSTEM switch button to select the JETS
mode. Sit or recline in the spa so you are comfortable.
Since the four jets are adjustable, you can direct a jet
toward any area where muscles feel tense or stiff. The
warmth of the water and the stimulating water flow from
the jet will pleasantly increase circulation.
Or, for the total whirlpool effect and allover feeling of
well-being, you can adjust all jets so they point in a
opposite directions to circulate the air and water mixture
in a circular motion all about the spa.
Water Rainbow Spout
The Water Rainbow spout will add the soothing sound of
a waterfall to your bathing pleasure, as well as provide
beautiful cascades of shimmering water for an exciting
visual effect.
Activate the waterfall feature by first turning on the JETS,
HTR/FILTER, or FILTER function, then rotate down-
ward the flow control lever located on the left side of the
spout. Use this lever to adjust the amount of water
flowing through the Water Rainbow spout. The waterfall
effect will be greatest in the JETS mode.
CAUTION
The water circulating through the Water Rainbow
spout is not fresh water and therefore is not suitable
for drinking.
Silent Air Induction
The intensity of the whirlpool action is determined by
how much air is inducted into the water. You have total
control of this by adjusting the air induction control knobs
located on bath control panels. For maximum air induc-
tion, rotate each control knob fully counter clockwise to
the largest circle. For fewer air bubbles, decrease the
amount of air induction by rotating the control knob
clockwise. When the knobs are turned to the smallest
circles, only water is being circulated.
Filtration
When you are ready to leave the spa, push the SYSTEM
switch button to turn off the whirlpool. Then select the
HTR/FILTER mode. Adjust the heater knob to the
temperature at which you wish the water maintained. In
this way, the water will be filtered when the heater goes
on to maintain the temperature. Running the filter pump
for at least one hour a day is sufficient. Another way to
be sure the water will be filtered is to set the built-in timer
in the electrical cabinet to turn on at a certain time to filter
the water for one hour. Be sure there is sufficient water
in the spa (filled to the water line indicator mark on the
skimmer/filter frame) when the timer is set, or the spa’s
motor/pump could be damaged. (See page 9 for instruc-
tions on setting the timer.)
12
DIRECTIONALLY ADJUSTABLE
WHIRLPOOL JET
Air Blower
The Aero Plus features a built-in air blower and factory
drilled air holes in the seats of the spa to add to your
enjoyment.
The blower sends air to a channel located under the
spa’s seats; this air is distributed through the air holes,
tiny bubbles are formed. These bubbles travel upward
through the water and expand until they reach the
surface and burst. The exciting visual effect of the
bursting bubbles contributes to the overall hydromas-
sage experience.
Activate the blower by pushing the ACCESSORY switch.
Note that when the blower is on, the low speed of the
motor turns on to activate the pump which allows filtra-
tion of the water and the use of the Water Rainbow
feature. However, while the blower is operating (in the
115V system), neither the jets nor the heater will func-
tion. If the heater mode has been selected, the heater
will come on again automatically when the blower is
turned off.
FULLYADJUSTABLE
WHIRLPOOL JET
