background image

2    CONTROLS

en-10

2.6

WARNING LIGHTS _________________________________________________________

The R-311 mower monitors vital machine systems. It uses a
combination of warning lights and an audible alarm to alert
the operator of conditions requiring immediate action.
When an alert occurs follow the general guidelines listed in
the chart below, and any specific actions outlined by the
grounds superintendent or service manager.

To test alarm system:

Turn ignition switch to RUN. The engine oil light 

(T

1

)

 and

charge pressure light 

(T

3

should come on. All lights should

go out once engine is started. 

Press horn/test switch 

(I)

. Horn will sound and Engine

Coolant Temperature 

(T

2

)

, Return Filter 

(T

4

)

, Hydraulic Oil

Temperature 

(T

5

)

, Charge Filter 

(T

6

)

, and Air Filter 

(T

7

)

lights will come on.

With engine off, press glow plug switch 

(U)

. Glow plug light

(T

8

will come on.

Turn signal lights 

(T

9

)

 are only used with the optional cab

installed.

This system monitors:
T1. Engine oil pressure
T2. Engine coolant temperature
T3. Charge pressure
T4. Hydraulic return oil filter
T5. Hydraulic oil temperature
T6. Hydraulic charge filter
T7. Air filter
T8. Glow Plug

Figure 2D

Alert

Action

T1.

Engine Oil Pressure

 - Alarm

sounds and oil pressure light
comes on. Oil pressure low.

Stop mower immediately, lower implements

 

and shut off engine!

 Inspect

oil level in engine. If oil light remains on with oil at proper level, shut off engine and
tow or trailer mower back to service area. 

NEVER

 operate engine with oil light on,

severe damage to the engine can occur.

T2.

Engine Coolant Temperature

Horn sounds. Engine coolant
temperature high.

Stop mower immediately, lower implements and shut off engine!

Remove debris such as leaves and grass clippings that may be restricting air flow
through rear screen on hood and area between radiator and oil cooler. If engine
continues to run hot, return mower to service area.

CAUTION

: Engine coolant is under pressure. Turn engine off and allow

fluid to cool before checking fluid level or adding coolant to radiator.

T

1

T

9

T

2

T

3

T

4

T

5

T

6

T

7

T

8

T

9

J-T XXXXXX-XX

77

93

˚ C

170

200

˚ F

10

16

12 14

VOLTS

SOLID

STATE

HOURS

0 0 0 0

0

10

10

10

30

30

10

10

10

10

30

30

10

M

Q

U

Y

J

N

R

V

Z

K

O

S

W

AA

L

P

T

X

Summary of Contents for R-311T

















































Reviews: