Jacobsen HR6010 ROPS Cab Operator'S Manual Download Page 6

August 2011© 

Jacobsen HR6010 ROPS Cab Operator Manual

 

 

 

Safe Operation on Rough Terrain 

 

1. Drive the mower slowly on hillsides and  curves to eliminate the danger of  tipping. Avoid 

slopes which are too steep for safe operation. Avoid sharp uphill turns. 

2. Always drive slowly enough over rough ground or obstructions. Drive at speeds slows enough 

to ensure your safety. 

3. When driving out of a ditch, gully, or  up a steep hillside, engage the clutch  slowly. Avoid 

sharp uphill turns. 

4. When descending steep grades, select a  sufficiently low gear to maintain control  with 

minimum use of braking. 

5. Use caution when driving near the edge of a ditch or gully. It may cave in, causing the mower 

to roll over. 

6. Be alert when operating near trees, slopes and around obstructions. Tree branches can cause 

damage to ROPS components. 

 

 

Maintenance Safety 

 

1. Remove mud, crop residue, chains, and tools from steps and operator’s platform. They may 

interfere with pedal operation or entry/exit from mower. 

2. When servicing components are too high to reach from the ground use steps and handholds. 

Do not use fenders or shields that are not designed as steps. 

 

 

Safe Highway Operation 

 

1. Before operating the mower on, or near, public roadways check with your local authorities 

for any local regulations that will affect you. 

2. Equip towed implements with slow moving vehicle (SMV) signs when traveling on public 

roads. 

3. Install additional lights on implement rear to safeguard against rear end collisions. 

4. Use hazard warning flashers as required by law when transporting or driving on public roads. 

If the mower had warning flashers removed when mounting the ROPS, they must be replaced 

prior to operation on public roads. 

5. Keep to the right, yielding right-of-way traffic, especially if pulling implements. Pull off the 

road and stop to allow motorists to pass. Drive on the road shoulder, if permitted by law. 

6. Use extreme caution when pulling heavy loads at road speeds. Avoid hard application of the 

mower brakes at high speed. 

7. Always drive slowly near curbs, approaches or ditches. 

8. If equipped, ensure headlights are aligned so they will not blind the operator’s of oncoming 

vehicles. If the mower is not equipped with turn signals and law requires them, install them 

prior to operating on or near public roads. 

Summary of Contents for HR6010 ROPS Cab
























Reviews: