Jacobsen Greens King 500A 63281 Technical Manual Download Page 12

Page: 12 / 60

3 DECALS

DECALS

3.1 DECALS _________________________________________________________________

Familiarize yourself with the decals, they are critical to the safe operation of the mower.
REPLACE DAMAGED DECALS IMMEDIATELY.

WARNING

1. Read operator

manual. Do not allow

untrained operator

to u

e machine.

2. Keep

hield

in place and hardware

ecurely ti

htened.

. Before you clean, adju

t or repair thi

equipment, di

e all drive

, en

parkin

brake and

top en

ine.

4. Keep hand

, feet and clothin

away

from movin

part

5. Never carry pa

6. Keep by

tander

away

CAUTION

ALLOW ENGINE
TO COOL FOR 2

MINUTE

BEFORE

REFUELING

WARNING

Keep By

tander

Away. Do

Not Operate Without Guard

In Place.

Vehicle Ma

Model PGM 19

4.0 K

Model PGM 22

5.0 K

Model 51

A 95.

Model 522TA 100.7 K

Model 522A 101.2 K

Model 526A 12

.4 K

Model TC22 101.1 K

11102

CAUTION

URE THE TRACTION CLUTCH

LEVER I

IN NEUTRAL BEFORE

TARTING THE ENGINE

001790

4127

WARNING

TO PREVENT INJURY AND ACCIDENTAL
CLUTCH ENGAGEMENT DO NOT ADJU

ENGINE

PEED U

ING THROTTLE LEVER

ON ENGINE. ALWAY

ADJU

T ENGINE

PEED U

ING THE OPC HANDLE AND

THROTTLE PADDLE.

41466

4169

40 REV A

DANGER

Keep hands and feet
away from the cutting
unit to prevent serious
injury.

DANGER

1. Keep a safe distance from the
machine. Keep bystanders
away.

2. Properly dispose of
components from this machine.
Refer to local regulations for
waste disposal and recycling.

3. Refer to the manual for
maintenance and service
procedures.

4. Do not spray water at
electrical components, engine
or clutch. Remove battery pack
before pressure washing unit.

Summary of Contents for Greens King 500A 63281





























































Search results

Summary of Contents for Greens King 500A 63281

Reviews:

Related manuals for Greens King 500A 63281

Brands by name

Popular brands

Jacobsen Greens King 500A 63281, Technical Manual

Search results

Summary of Contents for Greens King 500A 63281

Reviews:

Related manuals for Greens King 500A 63281

Brands by name

Popular brands