background image

 

8

INSTALLATION CLEARANCES

Ice Maker Installation

 

Unpacking 

 

 

 

 

 

 

Remove packaging materials 

IMPORTANT: Do not remove any permanent instruction labels or the data label on your ice 
maker. 

Remove tape and glue from your ice maker before using. 

 

To remove any remaining tape or glue, rub the area briskly with your thumb. Tape or glue 
residue can also be easily removed by rubbing a small amount of liquid dish soap over the 
adhesive with your fingers. Wipe with warm water and dry. 

 

Do not use sharp instruments, rubbing alcohol, flammable fluids, or abrasive cleaners to 
remove tape or glue. These products can damage the surface of your ice maker. 

Cleaning before use 

After you remove all of the packaging materials, clean the inside of your ice maker before using 
it. See "Interior cleaning" in the 

Cleaning and Maintenance

 section. 

Location Requirements   

 
 

 

 

 

 

 

 

 

 

 

 

 

Excessive Weight Hazard 

Use two or more people to move and install ice maker. 

Failure to do so can result in back or other injury. 

Top View 

Side View 

Rear   of   uni t

Front   of   uni t

1/ 5"

Si de

1/ 5"

Si de

2/ 5"

Top  of   uni t

1"

Summary of Contents for BBQ10700



























Reviews: