background image

8

All dimensions in millimetres with inch equivalents in brackets.

Dimensions and Weights

Trouble Shooting

Bowl fills when toilet not 

• 

in use

 Shut Seacocks.

Fit Vented Loops

Waste water re-appears 

• 

in bowl

Check Bottom Valve Gasket 

(16) and Joker Valve (33).

Bowl does not empty & 

• 

difficult to push handle 
down

Open Outlet Seacock.

Fully shut Flush Control Lever 

(23).
 Check Joker Valve (33), 

Discharge Hose or Outlet 
Seacock for blockage.

 

• 

Bowl does not empty 
and difficult to pull 
handle up

 Remove pump and check for 

blockage.

Bowl does not empty 

• 

although handle is easy 
to push & pull

Check Piston O-ring (30), 

Bottom Valve Gasket (16) & 
Joker Valve (33).

 

• 

Water does not come in 
and handle springs up if 
pushed down

 Open Inlet Seacock.

 Fully open Flush Control 

Lever (23).

Water does not come in  

• 

although handle is easy 
to push and pull

Open Flush Control Lever 

(23).
 Check Top Valve Gasket (21) 

and Piston O-ring (30).
Check Inlet Hose connections 

are airtight.

 

• 

Flush water is slow to 
appear during pumping

Shorten Inlet Hose from main  

Seacock.
Do not fit Vented Loop 

between Inlet Seacock & 
Pump
Fit between Pump & Bowl.

 Fit Non-Return Valve (29295-

1011) next to Inlet Seacock.

View X-X outline

(showing base fixing holes)

Diam. 19mm 

(0.75") I.D. 

Hose inlet 

Diam. 38mm (1.5") 

I.D. Hose outlet 

(multi angle) 

4 holes Diam. 9mm (0.35")

Model No

Description

Net Weight

A

B

C

D

E

F

G

29090-3000

MANUAL TOILET COMPACT BOWL

9.5kg
(21lb)

335 

(13.19)

615
(24.21)

247
(9.72)

425
(16.73)

485
(19.09)

450
(17.72)

165
(6.50)

mm
(ins)

29120-3000

MANUAL TOILET REGULAR BOWL

10.9kg 

(24lb)

345 

(13.58)

700
(27.56)

280
(11.02)

490
(19.29)

580
(22.83)

465
(18.31)

180
(7.09)

mm
(ins)

Summary of Contents for 29090-3000










Reviews: