The JK-
82 “Oasis” wireless alarm kit
1/2
MKE58105
The JK-82
“Oasis” wireless alarm kit
Installation of the JK-82 kit shall only be undertaken by technicians holding
a certificate issued by an authorized distributor. This simplified installation
manual only describes the basics, for more details see the manuals of
particular devices.
1. Factory-default pre-enrolled devices
Address Device
Note
05
JA-83M door detector
Delayed reaction
06
JA-83P PIR detector
Delayed reaction
48
RC-86 keyfob
Buttons
and
pre-enrolled
49
JA-81F keypad unit
Connect a magnetic door
sensor to its IN input
50
JA-80L indoor siren
2. Before installation
Have a SIM card ready for the GSM communicator which is
activated and does not require a PIN code to register to a GSM
network. If it is a prepaid card it should be sufficiently topped up.
3. Control panel and keypad installation
1.
Attach the Control Panel (CP)
to the desired location
2.
Insert the SIM card
into the communicator’s SIM card holder.
3.
Connect
back-up battery to the CP
(attach it securely with
adhesive tape).
4.
Connect the mains
to the CP
– its green LED will start flashing
5.
The communicator’s
red LED
should be lit during registration to
the GSM network, and
should turn off within 1 minute
.
If it
starts flashing instead, turn off the power (mains & battery) and
check that the SIM card functions properly in a mobile phone.
6.
Connect up the batteries in the JA-81F keypad
–
service
mode
should be displayed
(if not, disconnect the keypad
batteries, check that the control panel is powered up and
reconnect the keypad batteries).
The internal keypad menu can be entered in Service mode by
holding the
?
key. Using the arrows on keys 1 and 7 you can
scroll thought this menu:
Display
Key
Description
Tamper ON
Disable / Enable the tamper sensor
(only for service purposes)
Door chime ON
Disable / Enable sound when IN triggered
Beeper ON
Disable / Enable system sounds
Brightness
Sets the display brightness 0 - 9
Display
Key
Description
Contrast
Sets the display contrast 0 - 9
Edit text
Entry to keypads text editing
English
Sets English (reload default texts)
To exit the menu, press
#
(exiting also occurs after 10 seconds’ inactivity).
If you exit Service mode accidentally, it can be re-entered by
keying in
0 8080.
Close the keypad’s flip cover to save the battery while in the
service mode
7.
Enter
888 to measure the GSM signal
– it should be at least
2/4
(if it is not, find another location for the control panel or try
another provider’s SIM card).
8.
Exit GSM measurement mode
by pressing the
#
key.
9.
Before attaching the JA-81F keypad,
test that it functions
correctly at the desired location. We recommended
wiring up a
magnetic door sensor
(provided with the kit) to the keypad’s IN
input. This will ensure that th
e keypad is “woken up” whenever
the door is opened (to indicate system status, to make entrance
delay beeps and to have the access card reader ready for
reading cards).
4. Installing the detectors and the siren
1.
Install the JA-83M magnetic detector, select its reaction via the
internal DIP switch (INS/DEL), connect its battery and close the
cover.
B
A
B
+
B
A
B
reed contact
tamper
INSTANT
DELAY
serial number
battery CR123A
1
2
3
4
5
6
7
8
9
1
2
3
0
1
0
2
C
O
M
0
3
0
4
E
W
IW
P
G
X
P
G
Y
G
N
DAB
+
U
RESET
1 2 3 4
ON
OFF
Communicator
Main board
Transformer
Back-up battery
Mains terminal
Digital bus connector
GSM antenna
Tamper switch
SIM card
LEDs
Antenna
Mains fuse
Antena connector
Radio module
1
2
V
2
.4
A
h
