JA-80IR wireless optical barrier
2 /2
MKU52303
A permanently lit LED on the right indicates that the beam has been
interrupted (or wrongly adjusted). The better the beam reception, the
longer the breaks between the LED flashes. When the LED stops
flashing, continue looking for the ideal position indicated by the highest
voltage measured on the voltmeter.
Setting up the electronic part of the barrier
Both units are equipped with setting switches. The switch located on the side
of the units (on the optical part) allows barrier beam modulation frequency
adjustment from 1 to 4. This setting is useful only for a combination of
multiple JA-80IR barriers where a problem with interference might appear.
For more information see the original user.
There is a DIP switch with five switches. The first two positions are used to
set the reaction time to an interruption of the beam. The shorter the time, the
more precise the interruption detection, but also the greater the susceptibility
to false alarms during worsened optical conditions (snow, fog, ...)
Fig. 7 Reaction time setting
It is possible to set a 2-minute sleep time after an alarm (beam
interruption) in order to save batteries. This setting is done by switching
switch no. 3 (receiver unit), or no. 1 (transmitter unit) to the ON position.
Switches 4 and 5 (receiver unit), or better 2 and 3 (transmitter unit) are
set as a default and you should leave them in the OFF position for the
correct functioning of the device.
Operation testing
The LEDs on the barrier have the following indication functions
Receiver
Transmitter
Low battery LED
Low battery LED
Alarm LED
Power LED
Fig 8 LEDs on the units
The signal battery low LEDs flash when the batteries in the unit are low.
Both batteries
(SAFT LSH20 lithium batteries)
should always be
replaced at the same time.
The alarm LED flashes during beam blocking.
The power LED flashes when the battery in the transmitting unit is OK.
Receiver
Transmitter
Fig. 9 Barrier function test
Perform a barrier test in three places (A B and C). The setting is
completed only if the barrier reacts successfully in all three positions.
You should also check the signal transmission to the system control
panel. Only then is it possible to put back the unit covers and secure
them.
Checking the status of and replacing batteries
The detector checks battery status automatically and if the batteries are
running low, it informs the system. The detector remains fully functional.
The batteries should be replaced as soon as possible (within 1 week).
Use
SAFT LSH20 batteries exclusively
and always replace both at the
same time.
Technical specifications
Power supply
4x LSH20 type lithium batteries (3.6 V 13 Ah)
Average battery lifetime
approx. 3 years (with 120 s energy saving mode)
Operating frequency
868 MHz
Radio range – distance from the control panel
up to 300 m with direct visibility
Optex barrier parameters
Distance (max.) between the barrier units
60 m
Barrier installation height
0.7 – 1.0 m
Object motion speed
as set by user
Battery saving timer
120 s
Enclosure
IP55
Max. relative humidity of the environment
95%
Weight
1620 g
Environment according to EN 50131-1
class IV
Operating temperature range
-20°C to +60°C
Security grade
according to OPTEX
Comply with ETSI EN 300220, EN 50130-4, EN 55022, EN 60950-1
Can be operated according to
ERC REC 70 03
JABLOTRON ALARMS a.s. hereby declares that the JA-80IR
is in a compliance with the relevant Union harmonisation
legislation: Directives No: 2014/53/EU, 2014/35/EU,
2014/30/EU, 2011/65/EU. The original of the conformity
assessment can be found at www.jablotron.com - Section
Downloads.
Note:
Although this product does not contain any harmful
materials we suggest you return the product to the dealer or
directly to the producer after use.
88,1
21
7
162,5
83
,5
Fig. 10 Unit dimensions
