jablotron JA-162PB Manual Download Page 2

JA-162PB, JA-162PB-GR, JA-162PB-AN Wireless combined PIR 

motion and glass-break detector 

TYPE: 5PIRGBS2202OQ 

JA-162PB, JA-162PB-GR, JA-162PB-AN 

2 / 2 

MOQ51702 

Sensor of tearing-off from the wall:

 turns on/off the monitoring 

of an optional additional tamper contact on a JA-191PL joint holder. 

 

Detection characteristics 

The standard lens that is supplied with the JA-162PB detector covers 

an area of 90 degrees /12 m– see the following figure 3.  

 

 

Figure 3: Detection characteristics of PIR detector

 

 

 

Fig 4: Detection characteristics of the GBS sensor. 

Detector with a white lens (JA-162PB) offers standard protection 

against white light as required by regulation  (up to  6000 Lux). 

Detector with a grey (JA-162PB-GR) and black (JA-162PB-AN) lens 

offer increased protection against white light, well above the limits 

given by regulation (up to 10000 Lux).  

Note:

 when utilizing an alternative lens, test whether the detector 

covers the area correctly (an incorrectly installed lens can cause 

detection errors).

 

Detector testing 

While in service mode, the detector indicates each activation with 

its LED indicator. Once service mode is exited, the device enters 

normal operation.  During normal operation, LED indication is off, 

including  fault indication  –  yellow  LED  indication.  Each activation 

may be viewed within the 

F-Link

 software, within the 

Diagnostics

 

tab.  

Battery replacement 

The control panel automatically detects and reports low battery 

status. We recommend replacing the batteries within two weeks of 

the low battery status being reported. The batteries should be 

replaced by a service technician while the control panel is in Service 

mode. Always replace both batteries! 

After battery removal, it is necessary to wait for at least 10 s or 

close the detector without batteries before replacing them (this will 

activate the tamper contact (12) and discharge  the remaining 

energy). 

Notes:

 

 

If you insert an discharged  battery, the detector immediately 

detects it and starts indicating low battery status during the 

stabilization period (at least 15 s). 

 

The battery status can be monitored in the Diagnostics tab in  

the F-Link software. 

 

In order to make sure the detector works correctly, we 

recommend using the batteries supplied by a distributor (BAT-

3V0-CR123A) or other quality lithium batteries. 

 

Do not discard the battery into the trash; dispose of it at a waste 

collection point. 

Technical parameters 

Power 

2x Lithium battery CR123A (3.0 V/1.5 Ah) 

Please note: Batteries are not included. 

Typical battery lifetime 

approx. 3 years 

Low battery voltage 

 <2.7 V 

Quiescent current consumption 

50 uA 

Maximal current consumption 

50 mA 

Communication band 

868.1 MHz, protocol JABLOTRON 

Maximum radio-frequency power (ERP) 

<25 mW 

RF range 

500 m (open area) 

Recommended installation height 

2.5 m above the floor 

PIR detection angle/range 

90°/12 m 

GBS detection angle/range 

90°/9 m 

Dimensions 

150 x 63 x 40 mm 

Weight (w/o batteries) 

135 g 

Classification 

Security grade 2/Environmental class II 

 

(According to EN 50131-1) 

Environment 

indoor general 

Operating temperature range 

-10 °C to +40 °C 

Average operational humidity 

 75% RH, w/o condensation 

Certification body 

Trezor Test s.r.o. (no. 3025)  

In compliance with 

 ETSI EN 300 220-1,2, EN 50130-4, EN 55032,  

 

EN IEC 62368-1, EN IEC 63000, EN 50131-1, EN 50131-2-2,  

 

EN 50131-2-7-1, EN 50131-5-3, EN 50131-6. 

Can be operated according to 

ERC REC 70-03 

Recommended screw  

2 x 

 ø 3.5 x 40 mm (countersunk head) 

 

 

JABLOTRON ALARMS a.s. hereby declares that product 

5PIRGBS2202OQ is in a compliance with the relevant 

European Union harmonisation legislation: Directives No: 

2014/35/EU, 2014/30/EU, 2011/65/EU. The original of the 

conformity assessment can be found at www.jablotron.com – 

the Downloads section. 

 

Note:

  Disposing of this product correctly will help save 

valuable resources and prevent any potential negative effects 

on human health and the environment, which could otherwise 

arise from inappropriate waste handling. Please return the 

product to the dealer or contact your local authority for further 

details of your nearest designated collection point. 

 

Reviews: