The JA-150A II Internal wireless siren
The JA-150A II Internal wireless siren
2 / 2
MLP20100
Settings in accordance with security
grade 2
If security grade 2 is required, it can be configured by selecting
EN 50131, grade. 2.
from
System
profiles
located in the
Parameters
tab in the F-Link software. The device will be configured according
to the selected standard.
Siren indication priority
Fire alarm indication has the highest priority followed by IW and EW
alarm.
A lower indication priority belongs to interaction with the system
(setting/unsetting…) followed by indication upon activation of PG
outputs (PG1 has a higher priority than PG2 etc.). Indication with
a higher priority always terminates indication with a lower priority.
Priority levels of acoustic indication in descending order: Fire alarm,
IW/EW alarm, warning indication, unsetting the system with an active
alarm memory indication, Setting/Unsetting, Entrance/Exit delay, alarm
memory indication, PG output indication and finally, the siren flashes
an LED light when the status of the tamper sensor changes.
Battery replacement
A battery is included, however it is not factory-fitted in the siren
therefore it needs to be inserted into the device. The battery recharges
in a standard way (see
Technical specifications
). When replacement
is necessary, it is possible to order the BAT-3V2-CR2 replacement
battery. Connect it to the connector (see figure 1, point 2). The siren
automatically detects whether the battery is connected and performs
diagnostics. The measured values are then displayed in the F-Link
software. The siren monitors its own battery status and informs
a user (alternatively the service technician) when the battery is close
to being depleted. The device continues in its function however
it is recommended to replace the battery within 2 weeks. Use the BAT-
3V2-CR2 type of battery specifically.
The battery should be replaced by a service technician while
the control panel is in Service mode. Do not discard the battery
in the trash; dispose of it at a waste collection point.
Siren FW update
The siren supports wireless FW updates performed by the
F-Link
software while the control panel is in
Service
mode.
1. Click on the
Control panel
menu
Firmware update.
JA-150A
will appear in a dialog window. If F-Link contains newer firmware,
it will be selected automatically.
2. Confirm the update of the selected devices by clicking on the
OK
button.
3. When the FW update has finished, check the siren’s internal
settings in the
Devices
window
Internal settings.
4. Test whether the siren functions correctly.
Dimensions
Technical specifications
Power supply/wattage 110 - 230 V/50 -60 Hz, 0.6 W, protection class II
Connecting cables - maximum diameter
1.5 mm
2
Backup / recharge time
min. 24 h/max 72 h
Battery type
BAT-3V2-CR2/LiFePo4
Warning: Battery is not installed
Battery / lifetime
3.2 V; 470 mAh/3 years
/ minimum voltage when loaded
3.0 V
/ maximum voltage when unloaded
3.6 V
Communication band
868.1 MHz, JABLOTRON protocol
Communication range
approx. 300 m (open area)
Classification
security grade 2/environmental class II
- According to
EN 50131-1
- Alarm sound level
100 dB/1 m (±5 dB/1 m)
- Back up power supply
type W/24h back up
- Operational environment
indoor general
- Operating temperature range
-10 °C to +40 °C
- Average operational humidity
75 % RH, non-condensing
- Certification body
Trezor Test s.r.o. (no. 3025)
IP rating
IP43 according to EN 50131-1
Dimensions
80 x 80 x 35 mm
Also complies with
ETSI EN 300 220, EN 50130-4+A1:2014,
EN 55032:2015, EN 62368-1, EN 50131-5-3,
EN 50581:2012, EN 50131-4, EN 50131-6
Can be operated according to
ERC REC 70-03
JABLOTRON ALARMS a.s. hereby declares that the JA-150A II
is in a compliance with the relevant European Union
harmonisation legislation: Directives No: 2014/53/EU,
2014/35/EU, 2014/30/EU, 2011/65/EU.
The original of the conformity assessment can be found
at www.jablotron.com - Downloads Section.
Note:
Although this product does not contain any harmful
materials we suggest you return the product to the dealer
or directly to the producer after use.
