The JA-110C BUS photo verification camera
The JA-110C BUS photo verification camera
2 / 2
MNT51105
Note: A photo taken by a PG output activation is sent as the first one, photos
taken before an activation are sent subsequently and photos after
the activation sent last. In the MyJABLOTRON app photos are displayed
in the order they were taken.
Tampering detector (tilt detector):
(*Enabled) This option can disable the
reporting of a tamper alarm to the control panel in the case of tampering with
the camera (it does not have any influence on the tamper contact on the
camera cover). It can be used for problematic windy locations to eliminate false
alarms. However, by disabling the parameter you risk the camera being turned
to another direction without it being reported to the system. In such
a case we recommend you to enable the parameter “Tamper-activated
photos”.
Tamper-activated photos:
(*Enabled) This option can disable taking and
sending photos in the case of camera tampering. When
“
Photo buffering”
is disabled and the tilt detector is activated, the camera takes 3 photos with
a 5 s pause between them. When that parameter is enabled the camera takes
and sends photos according to the pre-set mode (respects its settings fully –
number of taken photos, time interval, etc.).
Note: Sometimes it could happen that photos will be taken at the same time
(duplication). This is determined by the camera’s internal algorithm.
IR supplementary illumination:
(*Auto)
The automatic function
of illumination by IR LED diodes of the camera is set in such a way that if the
ambient illumination drops below a certain level (dusk/sunset), the illumination
is automatically enabled. As soon as the ambient illumination level increases
(sunrise), the illumination is disabled. If the function “Pre-PG-Activation photos”
is “OFF”, the IR illumination is only activated on triggering of the PG and for
photos taken after the PG triggering. If “Always”
is selected,
IR illumination will be permanently on. IR illumination can also be completely
disabled (we recommend it when camera is place in an outdoor housing).
Higher IR illumination level:
(*Disabled) This option allows you
to increase the IR LED diode lighting intensity level.
Warning: the increase of the intensity level will cause a higher consumption
from the BUS (by up to 150 mA – 250 mA), you should check the total
consumption from the BUS to maintain the backup of the system.
External device triggering:
(*Disabled) When the option is enabled
the camera can use its internal illumination detector to trigger the PG. Select the
PG output in the camera internal settings in the Devices tab. By moving the
value between 0 (dark) and 10 (light) on the scale you determine under what
illumination conditions the PG is to be activated. To set the correct level for
particular illumination you can use the PG activation indicator located next to
the scale. When PG is ON the indicator goes red and when the PG is OFF the
indicator goes green.
Note: The controlled PG must have the “Copy” function (can be set
in the PG outputs tab).
Test:
It takes a one test photo in LQ and shows it in F-Link. Then when you
click on the Detail button photos are displayed in HQ. Photos are
simultaneously sent to the external mass storage area (if transfers are
enabled).
Saving and browsing the pictures
Some photos (activation photos which are not in Photo buffering mode and
photos taken when after PG has been triggered in Photo buffering mode) are
taken as a double exposure: the first with low resolution (LQ=320x240 pixels),
second with high resolution (HQ=640x480 pixels).
All exposures are saved in the internal memory (built-in SD card) into
the independent folders Foto_LQ and Foto_HQ. When the card is fully loaded,
the oldest photos are replaced by new ones. Photos saved on the SD card can
be browsed by a normal PC browser when the camera is connected via a USB
cable.
Photos are sent to the control panel in LQ. You can browse through
the images by
F-Link
and
J-Link
software (in the
Event memory
, click
on event
New image
). Pictures are displayed in LQ, if you click on
Detail
you
can get pictures of the second exposure HQ (if existing). Images can be
searched and browsed by a file manager or picture browser. For another
option to show the pictures it is necessary to start
F-Link
(
J-Link
) software and
be logged into the control panel as a service technician or Administrator and
then under Disc: Flexi_log/Foto photos are available which have been sent
to the control panel (LQ) and photos which have been requested in
Detail
(HQ).
Note: Some antivirus software writes checking data on the micro SD card.
The camera notices unknown files (the checking data) so formatting the SD
card will be performed. SD card formatting erases all data which has been
saved on the SD card.
Picture transmission from the control
panel to the MyJABLOTRON
If there is a SIM card supplied by the distributor and if the user uses
MyJABLOTRON services, then access to photos is automatically allowed.
Settings of the control panel for transferring pictures are done when the panel
is registered. All the photos are saved and visible in the MyJABLOTRON
application. The MyJABLOTRON application has an option to fill in telephone
numbers (for SMSes) or e-mails to get the photos when they are taken
(Notification). Using MyJABLOTRON it is also possible to request a new
picture without PG output activation (see
Installation recommendations).
Note: If the user doesn´t use or want to use the MyJABLOTRON application,
sending pictures straight from the control panel will work normally. The control
panel sends an SMS report to all selected users according to the
F-Link
software,
Users reports
tab,
Alarm photo
settings. Sent SMSes include an
http link for displaying the photo, which on cell phones with an internet
connection can be displayed directly.
CAUTION:
Because this camera allows you to take photos when the system
is unset by a PG state or from MyJABLOTRON, the producer strictly warns
the user that the camera has to be used within the limits given by particular
laws or norms, especially norms about the protection of personal privacy.
The use of the camera is also subject to regulations on the protection
of personal data and the producer recommends that users should be aware
of the obligations applicable to the operation of CCTV.
According to these regulations MyJABLOTRON users have an obligation
to ensure the approval of persons in the range of the camera during
the acquisition of photos or the obligation to indicate the image capture area
by information signs.
Installation recommendations
Several JA-110C cameras can be installed in the system. When several
cameras are triggered at the same time, the transmission time
to the control panel and outward is extended. A whole transmission can
take a few minutes. It is also necessary to pay attention to the current
peak from the control panel when requesting the new photo
by triggering more cameras with an external IR illumination (all at
the same time).
For taking photos by PG status set
PG outputs
/
Function
Impulse
to a time of at least 15 sec. via F-Link software. The camera has
an internal algorithm which limits taking the photos by PG status
to 3 photos per 10 minutes.
The camera has no internal counter of photos taken in a day.
The only limitation to the number of photos taken by a PG output
is a limit of 3 photos per 10 minutes.
Before you start using the MyJABLOTRON application or external
mass storage area check the cost of GPRS transfers with your
GSM provider.
If several PG outputs have been triggered at the same time
or getting buffered photos is being performed, the camera uses
already taken pictures so they could be duplicated.
The MyJablotron application copies these photos subsequently
to the correct events (switched PG outputs).
Technical specifications
Power
from the control panel BUS +12 V (+9 ... +15 V)
Current consumption in standby mode
15 mA
Current consumption for cable choice (IR higher intensity)
250 mA
IR illumination angle
70°
Horizontal camera capture angle
75°
Range of IR illumination
max. 12 m
Resolution of the camera
LQ 320*240; HQ 640*480 pixels
Average photo file size LQ/HQ (typically)
6kB/35kB
Typical (LQ) photo transmission time to the control panel
up to 20 sec. (10 sec.)
Typical (LQ) photo transfer time from the system to server
15 s/GPRS; 2 s/LAN
Operational environment according to EN 50131-1
IV. Outdoor general
Operational temperature range
-20 to +60 °C, humidity max. 75%
IP cover
IP65
Dimensions, weight
155 x 75 x 55 mm, 235 g
Classification
Grade 2
According to
EN 50131-1, EN 50131-3
Also complies with
EN 50130-4, EN 55022
JABLOTRON ALARMS a.s. hereby declares that the JA-110C
is in a compliance with the relevant Union harmonisation
legislation: Directives No: 2014/30/EU, 2011/65/EU.
The original of the conformity assessment can be found
at
www.jablotron.com
- Section Downloads.
Note:
Although this product does not contain any harmful
materials we suggest you return the product to the dealer
or directly to the producer after use.