GSM pager CA-1202 „Athos“
2/4
MHF52706
Figure 1:
installation of the GSM pager in Mode 3
6.1 Programming sequences
Enter the prescribed spaces in SMS texts as shown in the table below. MASTER is a factory default master code, which should be changed to your own
password. All SMS texts are case insensitive.
*
See part 5 for details.
SIM entry*
Text of SMS instruction
Description
RESET EN 3
MASTER RESET EN 3
Mode setting.
Factory default is 0 – no function (immobilization relay copies ignition).
Note: By
performing the RESET EN x instruction, all settings, remote controllers and enrolled wireless detectors
will be erased!
RESET is indicated by four siren chirps.
Not possible
MASTER UC uuuu
User Code setting
– the code (password) allows you to operate the alarm remotely via SMS from
unauthorized phones. uuuu is a new user code, up to 8 characters (A –Z & 0 – 9). Factory default
user code is USER
Not possible
MASTER MC xxxx
Master Code setting,
xxxx is a new master code, up to 8 characters (A –Z & 0 – 9).
The code allows you to change settings of the GSM pager. Factory default master code is MASTER
TEL1 xx...x
MASTER TEL1 xx...x
TEL2 xx...x
MASTER TEL2 xx...x
TEL3 xx...x
MASTER TEL3 xx...x
TEL4 xx...x
MASTER TEL4 xx...x
Setting of phone numbers to report alarms
(these phones will also be authorized to control the
GSM pager via SMS without a user password)
E.g.: MASTER TEL2 +420602123456 will enter the phone number into the TEL2 memory
MASTER TEL3 0 will erase the TEL3 memory.
DIAL1 xx...x
MASTER DIAL1 xx...x
DIAL2 xx...x
MASTER DIAL2 xx...x
DIALA xx...x
MASTER DIALA xx...x
DIALB xx...x
MASTER DIALB xx...x
Setting of phone numbers to dial using Hands free.
E.g.: MASTER DIAL2 +420602123456 will enter the number into the DIAL2 memory (which is dialed
after you press button
on the remote control)
MASTER DIAL2 0 will erase the memory DIAL2.
DIP abcdefghij
MASTER DIP abcdefghij
DIP parameter entry
– see part 7
SET abcdefghi
MASTER SET abcdefghi
SET parameter entry
– see part 8
Not possible
MASTER LEARN RC
Remote Control enrollment -
up to 4 controllers can be enrolled, turn the ignition key on before
sending the instruction. To enroll a remote control press and hold buttons
and
together for 3
seconds. After you enroll all remote controls, turn the ignition key off.
Not possible
MASTER TXT 01,text
Editing of SMS texts
(reports and instructions), see part 10
TELU xx...x
MASTER TELU xx...x
Sustain call setting
(for pre-paid cards) 1 x a month the xx..x number is called, call duration 10 s.
GSM pager CA-1202 „Athos“
3/4
MHF52706
7 DIP
parameters
By SMS:
MASTER DIP ABCDEFGHIJ
you can change 10 features:
Description
DIP
0
1
A
no function in Mode 3 (set to 0)
B Silent
alarm
Audible alarm
(30 sec.)
C
SMS alarm report only
SMS alarm siren sound
phone call
D
SMS remote control not
confirmed by SMS reply
SMS remote control instructions
confirmed by SMS reply
E
no function in Mode 3 (set to 0)
F
no function in Mode 3 (set to 0)
G
User can not change SMS
texts
User can change SMS texts by TXT
sequence
H
no function in Mode 3 (set to 0)
I
0 = Immobilization by arming and by SMS instruction
1 = Immobilization by arming and automatically 5 minutes after ignition is
turned off and also by SMS instruction
2 = Immobilization only by SMS instruction
J
Self-location disabled
The car´s location will be sent by
SMS to numbers TEL1 to TEL4 if
there is an alarm or if the car stops
after the immobilization SMS
instruction (See 13.6.)
Factory default setting is DIP 1111000000 (bold letters in the text). If you
want to change only particular parameters, enter x for the others (i.e.
MASTER DIP x0xxxxxxxx).
8 SET parameters
By SMS:
MASTER SET ABCDEFGHI
you can change 9 features:
Description
SET
0
1
A
no function in Mode 3 (set to 0)
B
no function in Mode 3 (set to 0)
C
no function in Mode 3 (set to 0)
D
Instant activation input logic:
0 = automatic
1 = activated by falling edge (grounding)
2 = activated by rising edge (disconnecting from GND)
E INP1
logic:
0 = automatic
1 = activated by falling edge (grounding)
2 = activated by rising edge (disconnecting from GND)
F
no function in Mode 3 (set to 0)
G
no function in Mode 3 (set to 0)
H
no function in Mode 3 (set to 0)
I
Do not switch off the GSM
module
Switch off the GSM module
after 30 minutes of idle
Factory default setting SET 100000010 (bold letters in the text).
If you want to change only particular parameters, enter x for the others
(i.e. MASTER SET xxx0xxxxx).
9 User instructions
9.1 Remote control by SMS instructions
SMS instructions sent from an authorized phone (TEL1 to TEL4) can operate
the GSM pager remotely. Factory default instruction texts are shown in the
following table. The instruction texts can be changed by SMS text editing,
see part 10.
If an SMS is sent from an unauthorized phone (other than TEL1 to TEL4), a
valid user code must be entered before the instruction (e.g. USER IMO).
SMS text
Description
IMO
STOP (immobilize) the car (after turning the ignition key off)
UNIMO
Unblock (mobilize) the car
STATUS
The GSM pager will reply with status information, e.g.
“car
reports: Time: 27.01.04 13:04, Status: Armed, Unblocked,
Ignition off“.
HELP
The GSM pager will reply with a brief list of SMS
instructions.
UC uuuu
To change the user code.
uuuu
is the new user code, up to
8 characters (A –Z & 0 – 9). Factory default user code is
USER
CREDIT
To obtain the balance of a prepaid SIM card if used. See
13.5 for details
HF abcdef
Hands-free set adjustment:
a – enable calls (
0= disabled
, 1=enabled)
b – auto answer incoming calls (
0= disabled
, 1=enabled)
c – microphone sensitivity 0 to 9,
(5)
d – speaker volume 0 to 9,
(5)
e - ringing tone volume 0=mute to 9=max.,
(5)
f – ringing sound 0 to 9,
(5)
LOCATOR
To obtain the car location from the GSM provider. See 13.4
•
The parameters in bold are factory defaults.
•
The instruction must contain spaces as shown in the table
•
Only basic ASCII can be used in the SMS instruction texts
•
If the SMS text contains the % sign, then the following text will be ignored.
9.2 Phone calls by an installed hands free set
If the optional HF-03 hands free set is installed, it is possible to receive
and make phone calls via the GSM pager. When the
ignition key is on
,
the remote control (RC-4x) allows you to operate the hands free set.
Incoming calls
– to answer them, press any button on the RC-4x remote
control. By pressing any button again, the call will be terminated.
When armed, all incoming calls are automatically rejected. If the car is
blocked (by IMO instruction) all calls are automatically answered (it is possible
to listen and to speak to the car remotely). Automatic call answering while you
are driving can also be enabled by the HF instruction (see 9.1).
To make a call
– you can call up to 4 preprogrammed numbers while you are
driving. By pressing button
,
,
or
on the remote control you will dial
the corresponding number (pre-programmed by DIALA to DIAL2, see 6.1)
9.3 Alarm
When an alarm is triggered, the siren will sound for 30 sec., warning SMS
messages will be sent to all phones (TEL1 to TEL4) and these phones will
also be called with the siren sound.
10 SMS text editing
The SMS texts (alarm information and instructions) are factory
preprogrammed. However, it is possible to change these texts by a
mobile phone or via internet access using
www.GSMlink.cz
To change a text by mobile phone, send the SMS:
MASTER TXT zz,text,zz,text,…
where:
zz
is the text index (see the following table)
text
is your new text – up to 30 characters, full stop (dot) or
comma cannot be used in the text, spaces are allowed
Example:
MASTER TXT 01,LOCK PLEASE
By changing text numbers 01 to 16, you will modify the control SMS
instructions. This allows you to customize the remote control of the car.
You can also make your own password part of the instruction to increase
the security of the mobile phone remote access.
10.1 SMS text table
zz Factory default text
zz
Factory default text
SMS commands:
34
Wireless detector
01 AM
35 Current
detector
02 DM
36 Telephone
1
03 IMO
37 Telephone
2
04 UNIMO
38 Telephone
3
05 STATUS
39 Telephone
4
06 HELP
40
Telephone - UC
07 CREDIT
41
Telephone - MC
08 DIAL
42 Remote
controller
09 HF
Status information:
10 LOCATOR
50
Car alarm reports:
11 MC
51 Status:
12 UC
52
Armed
13 DIP
53
Disarmed
14 TEL
54 Ignition
key
ON
15 LEARN RC
55
Ignition key OFF
16 LEARN
JA
56 Engine
is
blocked
17 SIREN
57 Engine
is
unblocked
18 SET
58 No
alarm
Events:
59 Alarm
timeout
20 Alarm
60
Low accumulator voltage
21
Alarm canceled by a user
61 Power
failure
22
Fire alarm
62 Power
recovery
23
Tamper alarm
63 Time:
24
Disarming
64 Low
battery
voltage
25
Arming
Confirmation SMS:
26 Low battery voltage
70
Command accepted
27 Engine is blocked
71
Command syntax error
28 Engine is unblocked
72
New MC code:
Source:
73 New
UC
code:
30 Ignition
key
74 Reset
31 Door contact
75
Registered phone number:
32 INP1
activation
76 Credit:
33
INP2 activation
77 LEARN
mode,
enrolled
The gray texts are not available in mode 3.
