GSM car alarm CA-1202 „Athos“
2/4
MHF52605
Figure 1:
installation of the car alarm in Mode 2
6.1 Programming sequences
Enter the prescribed spaces in SMS texts as shown in the table below. MASTER is a factory default master code, which should be changed to your own
password. All SMS texts are case insensitive.
SIM entry*
Text of SMS instruction
Description
RESET 2
MASTER RESET EN 2
Mode setting.
Factory default is 0 – no function (immobilization relay copies ignition).
Note: By
performing the RESET EN x instruction, all settings, remote controllers and enrolled wireless detectors
will be erased!
RESET is indicated by four siren chirps.
Not possible
MASTER UC uuuu
User Code setting
– the code (password) allows you to operate the alarm remotely via SMS from
unauthorized phones. uuuu is a new user code, up to 8 characters (A –Z & 0 – 9). Factory default
user code is USER
Not possible
MASTER MC xxxx
Master Code setting,
xxxx is a new master code, up to 8 letters (A –Z & 0 – 9).
The code allows you to change settings for the car alarm. Factory default master code is MASTER
TEL1 xx...x
MASTER TEL1 xx...x
TEL2 xx...x
MASTER TEL2 xx...x
TEL3 xx...x
MASTER TEL3 xx...x
TEL4 xx...x
MASTER TEL4 xx...x
Setting of phone numbers to report alarms
(these phones will also be authorized to control the
alarm via SMS without a user password)
E.g.: MASTER TEL2 +420602123456 will enter the phone number to TEL2 memory
MASTER TEL3 0 will erase the TEL3 memory.
DIAL1 xx...x
MASTER DIAL1 xx...x
DIAL2 xx...x
MASTER DIAL2 xx...x
DIALA xx...x
MASTER DIALA xx...x
DIALB xx...x
MASTER DIALB xx...x
Setting of phone numbers to dial using Hands free.
E.g.: MASTER DIAL2 +420602123456 will enter the number to DIAL2 memory (which is dialed after
you press button
on the remote control)
MASTER DIAL2 0 will erase the memory DIAL2.
DIP abcdefghij
MASTER DIP abcdefghij
DIP parameters entry
– see part 7
SET abcdefghi
MASTER SET abcdefghi
SET parameters entry
– see part 8
Not possible
MASTER LEARN RC
Remote Control enrollment -
up to 4 controllers can be enrolled, turn the ignition key on before
sending the instruction. To enroll a remote control press and hold buttons
and
together for 3
seconds. After you enroll all remote controls, turn the ignition key off.
Not possible
MASTER LEARN JA
JA-60 wireless detector enrollment –
up to 8 detectors can be enrolled, turn the ignition key on
before sending the instruction. To enroll a detector insert its battery. After you enroll all detectors, turn
the ignition key off.
Not possible
MASTER TXT 01,text
Editing of SMS texts
(reports and instructions), see part 10
TELU xx...x
MASTER TELU xx...x
Sustained call setting
(for pre-paid cards) 1x month the xx..x number is called, call duration 10 s.
*
See part 5 for details
.
GSM car alarm CA-1202 „Athos“
3/4
MHF52605
7 DIP
parameters
By SMS:
MASTER DIP ABCDEFGHIJ
you can change 10 features:
Description
DIP
0
1
A
0 = Silent arming/disarming without siren chirps
1 = 10 ms siren chirps when arming/disarming (non backed-up siren)
2 = 20 ms siren chirps when arming/disarming (backed-up siren)
B Silent
alarm
Audible alarm
(30 sec.)
C
SMS alarm report only
SMS alarm siren sound
phone call
D
SMS remote control not
confirmed by SMS reply
SMS remote control instructions
confirmed by SMS reply
E
0 = arming control by dialing in from TEL1 to TEL4 disabled
1 = arming control by dialing from TEL1 enabled
2 = arming control by dialing from TEL1 and TEL2 enabled
3 = arming control by dialing from TEL1, TEL2 and TEL3 enabled
4 = arming control by dialing from all TEL1 to TEL4 enabled
Arming and disarming by dialing from authorized phones is free of
charge
F
Arming control by dialing
in is not confirmed by
SMS
Arming control by dialing in (see E) is
confirmed by SMS to the phone
which dialed the car alarm
G
User can not change SMS
texts
User can change SMS texts by TXT
sequence
H
No function in mode 2 (set
to
0)
I
0 = Immobilization by arming and by SMS instruction
1 = Immobilization by arming and automatically 5 minutes after ignition is
turned off and also by SMS instruction
2 = Immobilization only by SMS instruction
J
Self-location disabled
The car´s location will be sent by
SMS to all TEL1 to TEL4 if there is
an alarm or if the car stops after
immobilization SMS instruction (See
13.6.)
Factory default setting is DIP 1111000000 (bold letters in the text). If you
want to change only particular parameters, enter x for the others (i.e.
MASTER DIP 0xxxxxxxxx will make arming control silent).
8 SET parameters
By SMS:
MASTER SET ABCDEFGHI
you can change 9 features:
Description
SET
0
1
A
Open door arming indication
disabled
Audible indication of arming with
open door
(4 beeps)
B
Voltage detector disabled
Voltage drop detector enabled
C
No function in mode 2 (set
0)
D
DOOR input logic:
0 = automatic
1 = activated by falling edge (grounding)
2 = activated by rising edge (disconnecting from GND)
E INP1
logic:
0 = automatic
1 = activated by falling edge (grounding)
2 = activated by rising edge (disconnecting from GND)
F INP2
logic:
0 = automatic
1 = activated by falling edge (grounding)
2 = activated by rising edge (disconnecting from GND)
G
Input for central locking signal logic
0 = automatic
1 = activated by falling edge (grounding)
2 = activated by rising edge (+12V)
H
Confirmation by the turn
lights is not required
Confirmation by the turn lights is
required
I
no function in Mode2
Factory default setting SET 100000010 (bold letters in the text).
If you want to change only particular parameters, enter x for the others
(i.e. MASTER SET 0xxxxxxxx will disable open door arming indication).
9 User instructions
9.1 Remote control arming and disarming
The alarm will be armed when the car is locked remotely by the original
remote control and disarmed when the car is unlocked remotely. The locking
(according to the setting in 8 H) and unlocking must always be followed by
confirmation from the turn lights. If the car is unlocked by the key (no
confirmation from the turn lights) then the alarm will be triggered. To stop the
alarm it is necessary to unlocked remotely by the original remote control. We
do not recommend installing the car alarm in this mode to cars in which
unlocking the door by key is confirmed by the turn lights (or disable this
feature if possible).
9.2 Remote control by SMS instructions
SMS instructions sent from an authorized phone (TEL1 to TEL4) can
operate the alarm
but
not the central locking
remotely. Factory default
instruction texts are shown in the following table. The instruction texts
can be changed by SMS text editing, see part 10.
If an SMS is sent from an unauthorized phone (other than TEL1 to
TEL4), a valid user code must be entered before the instruction (e.g.
USER AM).
SMS text
Description
AM
ARM and lock the car
DM
DISARM and unlock the car
IMO
STOP (immobilize) the car (after turning the ignition key off)
UNIMO
Unblock (mobilize) the car
STATUS
The car alarm will reply with status information, e.g.
„car
reports: Time: 27.01.04 13:04, Status: Armed, Unblocked,
Ignition off“.
HELP
The car alarm will reply with a brief list of SMS instructions.
UC uuuu
To change the user code.
uuuu
is the new user code, up to 8
characters (A –Z & 0 – 9). Factory default user code is
USER
CREDIT
To obtain the balance of a prepaid SIM card if used. See 13.7
for details
HF abcdef
Hands-free set adjustment:
a – enable calls (
0= disabled
, 1=enabled)
b – auto answer incoming calls (
0= disabled
, 1=enabled)
c – microphone sensitivity 0 to 9,
(5)
d – speaker volume 0 to 9,
(5)
e - ringing tone volume 0=mute to 9= max.,
(5)
f – ringing sound 0 to 9,
(5)
LOCATOR
To obtain the car location from the GSM provider. See 13.6
for details.
•
The parameters in bold are factory defaults.
•
The instruction must contain spaces as shown in the table
•
Only basic ASCII can be used in the SMS instruction texts
•
If the SMS text contains the % sign, then the following text will be
ignored. Characters %% in the message stop processing the
following text. Using these characters is suitable when sending an
SMS from an internet gateway which ads another text –
advertisements etc. When using the % character it is
always
necessary to insert the Master or User code followed by a space
before the command itself.
9.3 Dialing-in remote control
If enabled by the DIP parameters (see 7), the car alarm can be armed
and disarmed remotely by dialing in from an authorized phone (TEL1 to
TEL4). The car alarm will not answer the incoming call, but when it
recognizes your number, it will change status (Arm or Disarm).
Such remote control is free of charge since the phone is not answered.
Warning – if you dial your car alarm accidentally it can cause disarming of
the alarm.
Controlling by dialing in will result only in arming/disarming the alarm but
it will not lock/unlock the doors
Phone calls by an installed hands free set
If the optional HF-03 hands free set is installed, it is possible to receive
and make phone calls via the car alarm. When your car is
disarmed and
ignition key is on
, the remote control (RC-4x) allows you to operate the
hands free set.
Incoming calls
– to answer them, press any button on the RC-4x remote
control. By pressing any button again, the call will be terminated.
When armed, all incoming calls are automatically rejected. If the car is
blocked (by IMO instruction) all calls are automatically answered (it is
possible to listen and to speak to the car remotely). Automatic call
answering while you are driving can also be enabled by the HF
instruction (see 9.2).
To make a call
– you can call up to 4 preprogrammed numbers while you
are driving. By pressing button
,
,
or
on the remote control you
will dial the corresponding number (pre programmed by DIALA to DIAL2,
see 6.1)
9.4 Alarm
When an alarm is triggered, the siren will sound for 30 sec., warning SMS
messages will be sent to all phones (TEL1 to TEL4) and these phones will
also be called with the siren sound.
To stop the alarm,
disarm
the alarm by unlocking the doors using the
original remote control or by the disarm SMS instruction (DM).