![background image](http://html2.mh-extra.com/html/jabiru/j160/j160_technical-manual_3118859241.webp)
Aircraft Technical Manual
Jabiru Aircraft
Pty Ltd
J120, J160, J170, J200/J400, J230/J430, J250/J450 Variants
This document is controlled while it remains on the Jabiru server. Once this no longer applies the document becomes uncontrolled.
ISSUE
1
2
3
4
5
Dated: 29th October 2014
Issued By: AS
Page: 241 of 298
CAUTION
The Spinner is an important and integral part of the propeller Assembly. It is essential to ensure
adequate engine cooling. The aircraft must not be flown with the Spinner removed.
9.6
To Remove Existing Propeller (all J-Series)
1.
Remove Machine Screws and Tinnerman Washers from Spinner.
2.
Remove Spinner.
3.
Unbolt Propeller Bolts - 6 off.
4.
Remove Bolts, Spinner Flange, Aluminium Propeller Flange, Belleville Washers and Propeller.
9.7
To Assemble And Replace Propeller Assembly (all J-Series)
1.
Ensure that Propeller drive bushes
– 6 off, are in place in the Crankshaft Propeller Flange. Fit the
rear spinner backing plate to the flange.
2.
Fit propeller to flange. Ensure that the drive pins are snug fit in the propeller. Loose pins can
cause propeller fretting and engine damage.
3.
Fit Propeller Bolts - 6 off.
4.
Fit front spinner backing plate to front of propeller. The fit Aluminium Propeller Flange, Belleville
Washers - 42 off: (8 per Bolt: assembled in pairs as shown)
5.
Progressively tighten bolts ensuring equal distribution of load and in a normal criss-cross torque
sequence.
6.
Using Torque Wrench, tighten Bolts to 6lb.ft (72 inch.lbs).
7.
Check tracking of Propeller by locating a fixed object on a flat floor so that it just clears the
Propeller tips when rotating the Propeller by hand. Check that each blade clears the object by
the same amount. If the Propeller is outside the approved tolerance, refer to JABIRU Aircraft Pty
Ltd or a JABIRU Approved Service Centre.
Maximum Tracking Error Tolerance is +/- 2mm.
8.
Locate Spinner on Spinner Flange and fix with Machine Screws through Tinnerman Washers.
9.
Check Spinner for balance by locating a fixed object on a flat floor to just clear the lower edge of
the front dome of the Spinner. Rotate the propeller by hand and check that the Spinner runs true.
10.
Correct any imbalance by loosening and retightening Machine Screws.
9.8
Servicing And Repairs (all J-Series)
Required Tools:
Fine grit Sand paper
Parts and Material:
Propeller Repair Kit (p/n PP0049N)
Clear Epoxy Paint
Type of Maintenance:
Heavy Maintenance
Level of Certification:
L2 or LAME (A&P or LSA Repairman / Maintenance)
Return to Service:
L2 or LAME (A&P or LSA Repairman / Maintenance)
Any service or repair must take account of the risk of subsequent Propeller failure. Therefore repairs
are limited to the filling of small nicks in the Propeller. Maximum size of nicks approved for repair is:
-
Those in Leading Edge: 4mm deep x 20mm long
-
Those across the drive Face (flat sides): 2mm deep x 6mm diameter or scratches not more than
0.5mm deep.
Repairs must also take account of the changes to balance of the Propeller and therefore the
Propeller should be removed in accordance with the procedure described above. It must be checked
for balance (Section 9.9) prior to refitting (Section 9.7), checked for tracking after reassembly
(Section ) and the Spinner checked for balance after reassembly (see Paragraph 6.7).
Only nicks within the size tolerances described above may be repaired. All propellers with cracks or
splits (or any delamination of the composite sheath in the case of sheathed Propellers) must be