J.Sikora KV12 Manual Download Page 21 | Manualshive

Page: 21 / 24

J.Sikora KV12 Manual Download Page 21

J.Sikora

–

Standard MAX

Turntable Manual

21

© 2021 Notable Audio Products | www.notableaudio.com

8.

Adjusting Geometry

A J.Sikora Protractor is provided for
you. If you use this Protractor to set
the fine geometry for your cartridge,
the stylus should be in both null points
on the protractor (66mm, 120.9mm).

However, if you already have a more
sophisticated alignment tool, we
encourage you to use it.

J.Sikora Protractor

9.

Adjusting Azimuth

An important part of properly setting
up a tonearm is making sure the
Azimuth is correct. Azimuth refers to
the horizontal balance of the cartridge
when viewed from the front.

Your

KV12

or

KV12-VTA

Tonearm has

an Azimuth Weight that you can use to
make any necessary adjustments.

For minor Azimuth adjustments, use
the supplied Wrench and turn the
Internal Set Screw.

For large adjustments, slightly loosen
the Set Screw at the top of the Azimuth
Weight. Once the Screw is loose, rotate
the Azimuth Weight in the appropriate
direction until you achieve the correct
Azimuth. Once correct, tighten the Set
Screw again.

Azimuth Weight

Adjustments Points for Azimuth

10.

Adjusting Anti-Skate (Bias)

Null

Points

Azimuth

Weight

Set Screw for

Large

Adjustments

Internal Set Screw for

Minor Adjustments

«
...
19
20
21
22
23
...
»

Summary of Contents for KV12

























Reviews:

No comments