iWorX VAV Series Installation Manual Download Page 1

© 2011 Taco Electronic Solutions, Inc.

1

Installation Guide

502-011

VAV Series Terminal Unit Controller

Self-Contained Interoperable Controller Model CM2

SUPERSEDES: November 17, 2010

EFFECTIVE: March 16, 2011

Plant ID: 001-3959

Table of Contents

VAV Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   2

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Representations and Warranties . . . . . . . . . . . . . . . . .   2
Applicable Documentation . . . . . . . . . . . . . . . . . . . . . .   3
Installation Instructions. . . . . . . . . . . . . . . . . . . . . . . . .   4

Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
General  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Static Electricity . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
FCC Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Before Installing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .   5

About this Document . . . . . . . . . . . . . . . . . . . . . . . . 5
Inspecting the Equipment  . . . . . . . . . . . . . . . . . . . . 5
What is Not Included with this Equipment . . . . . . . . 5
Equipment Location . . . . . . . . . . . . . . . . . . . . . . . . . 5
Selecting a Power Source . . . . . . . . . . . . . . . . . . . . 5

Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  5

Mounting the Device. . . . . . . . . . . . . . . . . . . . . . . . .6
Routing Cabling to the Device  . . . . . . . . . . . . . . . . .7
Grounding the Device. . . . . . . . . . . . . . . . . . . . . . . .8

Wiring Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . .  8

Connecting Input Devices. . . . . . . . . . . . . . . . . . . . .8
Connecting Output Devices . . . . . . . . . . . . . . . . . . .9
Other Connections . . . . . . . . . . . . . . . . . . . . . . . . . .9

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  10

Electrical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Mechanical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Troubleshooting  . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  12

Diagnostic LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Troubleshooting Tips  . . . . . . . . . . . . . . . . . . . . . . .12

Summary of Contents for VAV Series

















Reviews: