![background image](http://html1.mh-extra.com/html/ivt/hpc-1400b/hpc-1400b_instruction-manual_2097832010.webp)
10
EN
Instruction manual
WARNING! The use of an RCD or
other circuit breaker unit does not
release the operator from the safety
instructions and safe working
practices given in this manual.
∙
The main voltage must correspond to the one
marked on the labels and on this manual. Do not use
other sources of power.
∙
Before inserting the plug in the main socket, make
sure that the socket ratings are correct and correspond
to those indicated on the rating label on the appliance.
∙
Avoid body contact with grounded surfaces such as
pipes, radiators, ranges and refrigerators. This increases
risk of electric shock if your body is grounded.
CAUTION! Touching electrified parts
may cause death by electric shock or
burn.
∙
Never move the appliance by pulling at the cables.
∙
Do not abuse the cord. Keep it away from heat, oil,
sharp edges or moving parts.
∙
Always guide the connection line safely.
∙
Do not use power tools near flammable liquids or gases.
∙
Always disconnect the appliance from the mains
supply before transporting it to other places.
CAUTION! The appliance should
always be switched off at the mains
before disconnecting any plug and
socket connector or extension
cables.
∙
Never pass the appliance over its own cord or
extension cable, while the tool is working. Make sure
you always know where the cable is.
∙
Do not wire a power cable directly into your device
yourself. Instead, take the device to your nearest
authorized Service Center.
∙
To avoid danger, damaged power cord should
be replaced by manufacturer or its agent, or similar
qualified person.
∙
Immediately unplug the tool when its cable is
damaged or cut.
ATTENTION! DANGER OF ELECTRIC
SHOCK!
Consider working area environment. Do not expose
power tools to rain. Do not use power tools in damp or wet
locations. Keep work area well lit and dry. Try to prevent
the device from getting wet or being exposed to humidity.
Do not leave it outside overnight. Water entering a power
tool will increase the risk of electric shock.
∙
The power supply cable should be checked
regularly and, before using it, make sure the cable is
not damaged or worn out. If the cable is not in good
condition, do not use the appliance; take it to an
authorized service Center.
∙
When tool is used outdoor, only use an extension
cable that is suitable for outdoor use and which is
marked for this specific use. Keep it away from the
working area, from damp, wet or oily surfaces and away
from heat and flammable materials.
∙
Avoid any accidental starting: make sure that the
power switch (if present) is in the «off» position, before
plugging the tool in.
∙
Remove adjusting keys or wrenches before turning
the tool on.
∙
Do not use the tool if the switch does not turn the
tool on or off. Any tool that cannot be controlled with the
switch is dangerous and must be repaired.
WARNING! During the use of certain
power tools, some dust containing
chemicals known to cause cancer,
may occur.
Some of these chemicals are: lead from lead based
paints, crystalline silica from bricks and cement and other
masonry products, arsenic and chromium from chemically
treated lumber and other dangerous products. If dust is
present, your risk from these exposures varies, depending
on how often you do this type of work.
To reduce your
exposure to these chemicals, any time you do
pulverulent operations, work in a well ventilated area
and work with approved safety equipment, such as
dust masks that are specially designed to filter out
microscopic particles.
∙
If the appliance strikes a foreign body, examine the
device for signs of damage and carry out any necessary
repairs before restarting and continuing to work.
∙
If the appliance starts to vibrate abnormally, turn
it off and check for the cause immediately. Vibration is
generally a warning of trouble.
∙
Always switch off the appliance and wait until
the device completely stops whenever you leave
the machine, before carrying out maintenance,
before changing accessories, checking, cleaning,
troubleshooting or working on the appliance.
∙
It is forbidden to move or modify any of the internal
parts of the device.
Summary of Contents for HPC-1400B
Page 7: ...7 F9 F10 F11 F12 F13 10 8 15 17 19 HPC 1400B HPC 1400B HPC 1800B HPC 2500B ...
Page 66: ......
Page 67: ......