ITV ICE MAKERS ALFA Technical & Service Manual Download Page 25

Page: 25 / 27

NG DP

TECHNICAL SERVICE MANUAL

SPECIAL ADVICE CONCERNING R-404A REFRIGERANT



R-404A is a mixture of 3 liquid-phase gases. On evaporating, the 3 component gases separate



Always use the liquid phase valve (at the end of condenser or accumulator) for refills and

purges.



When replacing a compressor, wash inside of circuit with a suitable s pump, dry with

nitrogen gas, REPLACE THE DRIER WITH ONE SUITABLE FOR R-404A, which must

also have ANTI-ACID properties.



If you need to add oil, use one which is specific for R-404A (POE). If you are in doubt,

contact the machine manufacturer.



If there is a leak anywhere in the circuit where R-404A in the GAS phase, and a refill of

over 10% is required, then ALL THE GAS IN THE CIRCUIT MUST BE PURGED AND

THEN REFILL AS DESCRIBED PREVIOUSLY (LIQUID PHASE VALVE)

Summary of Contents for ALFA




























Search results

Summary of Contents for ALFA

Reviews:

Related manuals for ALFA

Brands by name

Popular brands

ITV ICE MAKERS ALFA, Technical & Service Manual

Search results

Summary of Contents for ALFA

Reviews:

Related manuals for ALFA

Brands by name

Popular brands