ITT Goulds Pumps CV 3196 i-FRAME Installation, Operation And Maintenance Manual Download Page 21

Page: 21 / 178

3.1.1 Part description CV 3196

3196

3796

HT 3196

CV 3196

LF 3196

3198

NM 3196

Casing

Impeller

Cover

Power end

Figure 9: CV 3196 part description

Table 4: Casing

This table describes the pump casing parts.

Part

Description

Discharge

Tangential with optional Connections for venting, flushing, and cleaning out solids.

Gasket

Fully confined

Mounting method

Integral foot support for maximum resistance to misalignment distortion due to piping
loads.

Standard flange

ANSI class 150 flat-face serrated flange

Impeller

The impeller is

•

fully open and recessed from the casing

•

equipped with curved vanes

•

screwed onto the shaft

The threads are sealed from the pumped liquid by a PTFE O-ring.

Cover

Standard seal

3.1 General description CV 3196

Model CV 3196 i-FRAME Installation, Operation, and Maintenance Manual

Summary of Contents for Goulds Pumps CV 3196 i-FRAME



















































































































































































Search results

Summary of Contents for Goulds Pumps CV 3196 i-FRAME

Reviews:

Related manuals for Goulds Pumps CV 3196 i-FRAME

Brands by name

Popular brands

ITT Goulds Pumps CV 3196 i-FRAME, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for Goulds Pumps CV 3196 i-FRAME

Reviews:

Related manuals for Goulds Pumps CV 3196 i-FRAME

Brands by name

Popular brands