ITT Goulds Pumps CV 3196 i-FRAME Installation, Operation And Maintenance Manual Download Page 106

Page: 106 / 178

This figure shows the areas to inspect for cracks on the C-face adapter.

Figure 89: C-face adapter inspection locations

6.5.5 Seal chamber and stuffing box cover inspection

Checklist

Perform these checks when you inspect the seal chamber and stuffing box cover:

•

Make sure that these surfaces are clean:

•

Seal chamber and stuffing box cover

•

Mounting

•

Make sure there is no pitting or wear greater than 3.2 mm | 1/8 in. deep.

Replace the seal chamber and stuffing box cover if pitting or wear exceeds this measurement.

•

Inspect the machined surfaces and mating faces noted in the figures.

These images point to the areas to inspect:

184

Figure 90: BigBore

chamber

6.5 Pre-assembly inspections

104

Model CV 3196 i-FRAME Installation, Operation, and Maintenance Manual

Summary of Contents for Goulds Pumps CV 3196 i-FRAME



















































































































































































Search results

Summary of Contents for Goulds Pumps CV 3196 i-FRAME

Reviews:

Related manuals for Goulds Pumps CV 3196 i-FRAME

Brands by name

Popular brands

ITT Goulds Pumps CV 3196 i-FRAME, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for Goulds Pumps CV 3196 i-FRAME

Reviews:

Related manuals for Goulds Pumps CV 3196 i-FRAME

Brands by name

Popular brands